-
Journal of the Mechanical Behavior of... Oct 2023The present work describes green-mediated copper oxide nanoparticles as a potential corrosion inhibitor for the dental alloy Ti-6Al-4V. The salt of copper was reduced to...
The present work describes green-mediated copper oxide nanoparticles as a potential corrosion inhibitor for the dental alloy Ti-6Al-4V. The salt of copper was reduced to metal nanoparticles using Murraya koenigii leaves, which helps with the agglomeration and nanocluster formation through a reduction mechanism. The current synthesis is a single-step process and is cost-effective. The synthesized nanoparticle was characterized using UV, FTIR, XRD, Zeta potential and Particle size analyzer, SEM, and EDX. The particles were then electrodeposited on Ti-6Al-4V alloy, and the corrosion resistivity in the dental medium was analyzed using Electrochemical parameters such as Corrosion current, Corrosion potential, and anodic and cathodic intercepts through the Tafel and Nyquist plots. The synthesized nanoparticles showed characteristic absorbance at 359 nm. FTIR peaks confirm the phytochemical constituents present in the Murraya koenigii that accounts for the formation of nanoparticles. The XRD predicts the crystalline nature, which is further studied using SEM and EDX. The Zeta potential and Particle size analyzer confirms the negative-negative interactive nature of the synthesized CuO NPs. The NPs showed explicit corrosion inhibition properties with an overall inhibition efficiency of 58.15% and 25.6%, respectively. The study confirms the advantage of using Copper Oxide nanoparticles as a potential coating agent in dental implant alloys in increasing its corrosion efficiency.
Topics: Corrosion; Copper; Murraya; Metal Nanoparticles; Alloys; Dental Alloys; Oxides
PubMed: 37643540
DOI: 10.1016/j.jmbbm.2023.106080 -
Biomaterials Advances Dec 2023Titanium and its alloy are clinically used as an implant material for load-bearing applications to treat bone defects. However, the lack of biological interaction...
Titanium and its alloy are clinically used as an implant material for load-bearing applications to treat bone defects. However, the lack of biological interaction between bone tissue and implant and the risk of infection are still critical challenges in clinical orthopedics. In the current work, we have developed a novel approach by first 1) modifying the implant surface using hydroxyapatite (HA) coating to enhance bioactivity and 2) integrating curcumin and epigallocatechin gallate (EGCG) in the coating that would induce chemopreventive and osteogenic potential and impart antibacterial properties to the implant. The study shows that curcumin and EGCG exhibit controlled and sustained release profiles in acidic and physiological environments. Curcumin and EGCG also show in vitro cytotoxicity toward osteosarcoma cells after 11 days, and the dual system shows a ~94 % reduction in bacterial growth, indicating their in vitro chemopreventive potential and antibacterial efficacy. The release of both curcumin and EGCG was found to be compatible with osteoblast cells and further promotes their growth. It shows a 3-fold enhancement in cellular viability in the dual drug-loaded implant compared to the untreated samples. These findings suggest that multifunctional HA-coated Ti6Al4V implants integrated with curcumin and EGCG could be a promising strategy for osteosarcoma inhibition and osteoblast cell growth while preventing infection.
Topics: Humans; Curcumin; Titanium; Durapatite; Anti-Bacterial Agents; Osteosarcoma; Bone Neoplasms
PubMed: 37979438
DOI: 10.1016/j.bioadv.2023.213667 -
The Journal of Arthroplasty Jul 2023Total hip arthroplasty (THA) failure due to tribocorrosion of modular junctions and resulting adverse local tissue reactions to corrosion debris have seemingly increased...
BACKGROUND
Total hip arthroplasty (THA) failure due to tribocorrosion of modular junctions and resulting adverse local tissue reactions to corrosion debris have seemingly increased over the past few decades. Recent studies have found that chemically-induced column damage seen on the inner head taper is enabled by banding in the alloy microstructure of wrought cobalt-chromium-molybdenum alloy femoral heads, and is associated with more material loss than other tribocorrosion processes. It is unclear if alloy banding represents a recent phenomenon. The purpose of this study was to examine THAs implanted in the 1990s, 2000s, and 2010s to determine if alloy microstructure and implant susceptibility to severe damage has increased over time.
METHODS
Five hundred and forty-five modular heads were assessed for damage severity and grouped based on decade of implantation to serve as a proxy measure for manufacturing date. A subset of heads (n = 120) was then processed for metallographic analysis to visualize alloy banding.
RESULTS
We found that damage score distribution was consistent over the time periods, but the incidence of column damage significantly increased between the 1990s and 2000s. Banding also increased from the 1990s to 2000s, but both column damage and banding levels appear to recover slightly in the 2010s.
CONCLUSION
Banding, which provides preferential corrosion sites enabling column damage, has increased over the last 3 decades. No difference between manufacturers was seen, which may be explained by shared suppliers of bar stock material. These findings are important as banding can be avoidable, reducing the risk of severe column damage to THA modular junctions and failure due to adverse local tissue reactions.
Topics: Humans; Hip Prosthesis; Vitallium; Chromium Alloys; Arthroplasty, Replacement, Hip; Femur Head; Corrosion; Prosthesis Failure; Prosthesis Design; Cobalt
PubMed: 37028774
DOI: 10.1016/j.arth.2023.03.091 -
Biomaterials Science Dec 2023Titanium (Ti) and its alloys are widely used in clinical practice. As they are not bioactive, hydroxyapatite (HA) is commonly used to modify them. This study offered a... (Review)
Review
Titanium (Ti) and its alloys are widely used in clinical practice. As they are not bioactive, hydroxyapatite (HA) is commonly used to modify them. This study offered a review of microwave-assisted synthesis of composites based on Ti and HA for dental implantation by exploring their interaction mechanisms with microwave and features of two main techniques, namely microwave coating and sintering, along with current challenges and potential solutions in the field. It was shown that microwave coating enables rapid deposition of HA, but suffers from problems such as uneven coating thickness, poor integrity and unstable composition of the products. They can be solved by creating interlayers, combining the spin coating technique, . Unlike microwave coating, microwave sintering can effectively modify the mechanical properties of the composites, despite the shortcomings of excessive elastic moduli and potential HA decomposition. These issues are expected to be addressed by adding alloying elements and employing appropriate materials as space holders and ion-doped HA for sintering.
Topics: Durapatite; Titanium; Microwaves; Surface Properties; Materials Testing; Alloys; Dental Implantation; Coated Materials, Biocompatible
PubMed: 37965798
DOI: 10.1039/d3bm01151h -
World Journal of Gastrointestinal... Jul 2023Recent advancements in endoscopy equipment have facilitated endoscopists' detection of neoplasms in the oral cavity and pharyngolaryngeal regions. In particular,... (Review)
Review
Recent advancements in endoscopy equipment have facilitated endoscopists' detection of neoplasms in the oral cavity and pharyngolaryngeal regions. In particular, image-enhanced endoscopy using narrow band imaging or blue laser imaging play an integral role in the endoscopic diagnosis of oral and pharyngolaryngeal cancers. Despite these advancements, limited studies have focused on benign lesions that can be observed during esophagogastroduodenoscopy in the oral and pharyngolaryngeal regions. Therefore, this mini-review aimed to provide essential information on such benign lesions, along with representative endoscopic images of dental caries, cleft palate, palatal torus, bifid uvula, compression by cervical osteophytes, tonsil hyperplasia, black hairy tongue, oral candidiasis, oral and pharyngolaryngeal ulcers, pharyngeal melanosis, oral tattoos associated with dental alloys, retention cysts, papilloma, radiation-induced changes, skin flaps, vocal cord paresis, and vocal fold leukoplakia. Whilst it is imperative to seek consultation from otolaryngologists or dentists in instances where the diagnosis cannot be definitively ascertained by endoscopists, the merits of attaining foundational expertise pertaining to oral and pharyngolaryngeal lesions are unequivocal. This article will be a valuable resource for endoscopists seeking to enhance their understanding of oral and pharyngolaryngeal lesions.
PubMed: 37547241
DOI: 10.4253/wjge.v15.i7.496 -
Clinical Oral Investigations Dec 2023To assess the clinical outcomes of zirconia dental implants based on an updated systematic literature review. (Meta-Analysis)
Meta-Analysis Review
PURPOSE
To assess the clinical outcomes of zirconia dental implants based on an updated systematic literature review.
METHODS
An electronic search was performed in three databases, last updated in June 2023, supplemented by hand searching. The eligibility criteria were clinical studies reporting patients rehabilitated with zirconia implants. The cumulative survival rate (CSR) of implants was calculated. A meta-analysis for marginal bone loss (MBL) under different follow-up times and a meta-regression assessing the relationship between mean MBL and follow-up were done.
RESULTS
Twenty-five studies were included (4017 implants, 2083 patients). Seven studies had follow-up longer than 60 months. 172 implants failed, after a mean of 12.0 ± 16.1 months (min-max 0.3-86.0), of which 47 early failures, and 26 due to implant fracture, the majority in narrow-diameter implants. The 10-year CSR was 95.1%. Implants with coronal part prepared by drills presented statistically significant lower survival than non-prepared implants (p < 0.001). Two-piece implants presented lower survival than one-piece implants (p = 0.017). Implants discontinued from the market presented lower survival than the commercially available ones (p < 0.001). The difference in survival was not significant between implants in maxilla and mandible (p = 0.637). The mean MBL fluctuated between 0.632 and 2.060 mm over long periods of observation (up until 132 months). There was an estimated MBL increase of 0.005 mm per additional month of follow-up.
CONCLUSION
Zirconia implants present high 10-year CSR and short-term low MBL. The review was registered in PROSPERO (CRD42022342055).
CLINICAL RELEVANCE
The clinical outcomes observed for zirconia dental implants are very promising, although these have not yet been extensively studied as titanium alloy implants.
Topics: Humans; Dental Implants; Treatment Outcome; Dental Restoration Failure; Zirconium; Titanium; Dental Prosthesis Design
PubMed: 38135804
DOI: 10.1007/s00784-023-05401-8 -
Materials (Basel, Switzerland) Sep 2023Titanium alloys have been present for decades as the main components for the production of various orthopedic and dental elements. However, modern times require titanium...
Titanium alloys have been present for decades as the main components for the production of various orthopedic and dental elements. However, modern times require titanium alloys with a low Young's modulus, and without the presence of cytotoxic alloying elements. Machine learning was used with aim to analyze biocompatible titanium alloys and predict the composition of Ti alloys with a low Young's modulus. A database was created using experimental data for alloy composition, Young's modulus, and mechanical and thermal properties of biocompatible titanium alloys. The Extra Tree Regression model was built to predict the Young's modulus of titanium alloys. By processing data of 246 alloys, the specific heat was discovered to be the most influential parameter that contributes to the lowering of the Young's modulus of titanium alloys. Further, the Monte Carlo method was used to predict the composition of future alloys with the desired properties. Simulation results of ten million samples, with predefined conditions for obtaining titanium alloys with a Young's modulus lower than 70 GPa, show that it is possible to obtain several multicomponent alloys, consisting of five main elements: titanium, zirconium, tin, manganese and niobium.
PubMed: 37834492
DOI: 10.3390/ma16196355 -
Journal of Biomedical Materials... Sep 2023Additive manufacturing (AM) of CoCrMo metallic implants is growing in the orthopedic and dental fields. This is due to the traditional alloy's excellent corrosion...
Additive manufacturing (AM) of CoCrMo metallic implants is growing in the orthopedic and dental fields. This is due to the traditional alloy's excellent corrosion resistance and mechanical properties. AM processes like selective laser melting (SLM) require less time, materials, and waste than casting or subtractive manufacturing complex-geometry structures (bridges, partial dentures, etc.). The objective of this work was to investigate the low cycle tribological and tribocorrosion characteristics of AM CoCrMoW alloys compared to wrought LC CoCrMo (ASTM F-1537) to assess this AM alloy's performance. Fretting and tribocorrosion testing was performed in air (wear only), PBS (wear + corrosion), and PBS with 10 mM H O (wear + corrosion + inflammation) by a single diamond asperity. No variation between alloys in volume of material removed (p = .12), volume of plastic deformation (p = .13), and scratch depth (p = .84) showed that AM was substantially similar in wear resistance to LC in air and PBS. AM exhibited significantly higher fretting currents (p < .01) at loads up to 100 mN ( = 57 nA and = 49 nA) than LC CoCrMo ( = 30 nA) and ( = 29 nA). In PBS, wear track depth linearly correlates to fretting current, averaged over 100 cycles. Additionally, fretting currents of both alloys were significantly lower in simulated inflammatory conditions compared to PBS alone. AM alloy has generally similar wear and tribocorrosion resistance to wrought LC CoCrMo and would be ideal for patient specific dentistry or orthopedics where precise, complex geometries are required.
Topics: Humans; Alloys; Materials Testing; Carbon; Corrosion; Orthopedics; Surface Properties
PubMed: 37081711
DOI: 10.1002/jbm.b.35258 -
Journal of Functional Biomaterials Jul 2023The objective of this experimental work was to examine and characterise the route for obtaining demonstrative temporary biodegradable personalised implants from the Mg...
The objective of this experimental work was to examine and characterise the route for obtaining demonstrative temporary biodegradable personalised implants from the Mg alloy Mg-10Zn-0.5Zr-0.8Ca (wt.%). This studied Mg alloy was obtained in its powder state using the mechanical alloying method, with shape and size characteristics suitable for ensuing 3D additive manufacturing using the SLM (selective laser melting) procedure. The SLM procedure was applied to various processing parameters. All obtained samples were characterised microstructurally (using XRD-X-ray diffraction, and SEM-scanning electron microscopy); mechanically, by applying a compression test; and, finally, from a corrosion resistance viewpoint. Using the optimal test processing parameters, a few demonstrative temporary implants of small dimensions were made via the SLM method. Our conclusion is that mechanical alloying combined with SLM processing has good potential to manage 3D additive manufacturing for personalised temporary biodegradable implants of magnesium alloys. The compression tests show results closer to those of human bones compared to other potential metallic alloys. The applied corrosion test shows result comparable with that of the commercial magnesium alloy ZK60.
PubMed: 37623645
DOI: 10.3390/jfb14080400 -
General Dentistry 2023Polyetheretherketone (PEEK) resin is a high-performance thermoplastic polymer that has been introduced as a possible candidate to replace metallic components in dental... (Review)
Review
Polyetheretherketone (PEEK) resin is a high-performance thermoplastic polymer that has been introduced as a possible candidate to replace metallic components in dental prostheses. The objective of this integrative review was to compare, through analysis of studies in the literature, the mechanical performance of removable partial denture frameworks and clasps manufactured with PEEK with the performance of cobalt-chromium (Co-Cr) frameworks and clasps. The guiding question was, "Does the use of PEEK as a substitute for Co-Cr alloys for the construction of removable partial denture frameworks result in better mechanical properties?" The PubMed/ MEDLINE, Embase, Web of Science, Scopus, and SciELO databases were searched for articles published through October 2021. The JBI Critical Appraisal Checklist for Quasi-Experimental Studies was used to assess the methodologic quality of the selected in vitro studies. A total of 208 articles were identified. After the exclusion of duplicates and articles that did not meet the inclusion criteria, 7 studies- -4 in vitro and 3 three-dimensional finite element analyses- -published between 2012 and 2021 were included in the integrative review. The appraisal checklist revealed that the reviewed studies had a low risk of bias and high methodologic quality. The results of the review showed that PEEK alloys have adequate mechanical properties for use in clasps and removable partial denture frameworks, but Co-Cr alloys exhibit better mechanical properties and are more suitable in most circumstances.
Topics: Humans; Denture, Partial, Removable; Dental Clasps; Chromium Alloys; Polymers; Polyethylene Glycols; Ketones
PubMed: 37358585
DOI: No ID Found