-
Dental Materials Journal Sep 2023We aimed to elucidate the effects of ultraviolet (UV) irradiation on the shear bond strength (SBS) between heat-cured polymethyl methacrylate (PMMA) and a Co-Cr-Mo...
We aimed to elucidate the effects of ultraviolet (UV) irradiation on the shear bond strength (SBS) between heat-cured polymethyl methacrylate (PMMA) and a Co-Cr-Mo alloy. Disk-shaped Co-Cr-Mo alloy prepared by casting were subjected to different UV treatment times (0, 15, and 30 min). To determine the effect of UV treatment on surface properties of the alloy, surface roughness, wettability, and chemical compositions were analyzed. To evaluate the SBS, cylindrical PMMA was bonded to the UV-treated alloy, and subsequently subjected to the SBS test after 24 h of storage at room temperature or following 10,000 thermal cycles (n=10/group). After the UV treatment, the surface roughness remained unchanged, but oxidation resulted in the surface exhibiting greater hydrophilic characteristics. The UV-treated group showed significantly higher SBS values than those of the non-treated group (p<0.001). These results suggested that UV treatment-mediated oxidation improved the bond strength between PMMA and Co-Cr-Mo alloy.
PubMed: 37612058
DOI: 10.4012/dmj.2023-058 -
BMC Oral Health Sep 2023To analyse the changes in surface and nickel ion release characteristics of fractured root canal shaping instruments in a simulated body fluid environment.
BACKGROUND
To analyse the changes in surface and nickel ion release characteristics of fractured root canal shaping instruments in a simulated body fluid environment.
METHODS
A total of 54 new instruments were studied. The instrument groups consisted of five different NiTi alloys and a stainless-steel alloy. To standardize instrument fracture, a torsional type of failure was created on each instrument. The fractured specimens of each instrument group were randomly divided into three static immersion subgroups of 1 h, 7-day, and 30-day (n = 3). Simulated body fluid (SBF) was prepared to mimic human blood plasma by Kokubo&Takadama protocol for ex situ static immersions at 37ºC. The surfaces were examined via scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy. To determine the quantitative ion release, the retrieved SBFs were analyzed using inductively coupled plasma mass spectrometry. Two-way ANOVA and Tukey post hoc tests sought the statistical significance of the nickel ion values(p < 0.05).
RESULTS
In 1 h of immersion, the newly formed structures, exhibiting mostly oxygen signals, were widespread and evident on NiTi surfaces. In contrast, fewer structures were detected on the SS surface in that subgroup. In 7 days of immersion, a tendency for a decrease in the density of the new structures was revealed in NiTi groups. The oxygen signals on NiTi group surfaces significantly increased, contrary to their decrease in SS. Signals of sodium, chlorine, and calcium were detected, indicating salt precipitates in groups. In 30 days of immersion, salt precipitates continued to form. The Ni-ion release values in all instrument groups presented significant differences in comparison to the SBF control in all immersion periods(p < 0.001). No significant differences were observed in immersion time periods or instrument groups(p > 0.05).
CONCLUSIONS
Within the limitations of the presented study, it was concluded that the fractured SS and NiTi root canal instruments release Ni ions in contact with body fluid. However, the Ni ion release values determined during the observation periods are lower than the critical toxic or allergic thresholds defined for the human body. This was due to the ionic dissolution cycle reaching a stable state from 1-hour to 30-day exposure to the body fluid of fractured instruments.
Topics: Humans; Nickel; Root Canal Therapy; Alloys; Dental Alloys; Titanium; Ions; Root Canal Preparation; Surface Properties; Materials Testing; Equipment Design
PubMed: 37777753
DOI: 10.1186/s12903-023-03434-9 -
Odontology Apr 2024This study aims at evaluating the effect of simulating porcelain firing on the microstructure, corrosion behavior and mechanical properties of a Co-Cr-Mo alloy...
This study aims at evaluating the effect of simulating porcelain firing on the microstructure, corrosion behavior and mechanical properties of a Co-Cr-Mo alloy fabricated by Metal Soft Milling (MSM). Two groups of Co-28Cr-5Mo specimens (25 × 20 × 3 mm) were prepared by MSM: The as-sintered (AS) specimens and the post-fired (PF) specimens that were subjected to 5 simulating porcelain firing cycles without applying the ceramic mass onto their surface. Phase identification by X-ray Diffraction (XRD), microstructure examination by optical microscopy and Scanning Electron Microscopy combined with Energy-Dispersive X-ray Spectroscopy (SEM/EDX), corrosion testing by cyclic polarization and chronoamperometry in simulated body fluid (SBF), the latter test accompanied by Cr and Cr detection in the electrolyte through the 1.5-diphenylcarbazide (DPC) method and UV/visible spectrophotometry, and mechanical testing by micro-/nano-indentation were conducted to evaluate the effect of the post-firing cycles on the properties of Co-Cr-Mo. The results were statistically analyzed by the t test (p < 0.05: statistically significant). All specimens had a mixed γ-fcc and ε-hcp cobalt-based microstructure with a dispersion of pores filled with SiO and a fine MC intergranular presence. PF led to an increase in the ε-Co content and slight grain coarsening. Both AS and PF alloys showed high resistance to general and localized corrosion, whereas neither Cr nor Cr were detected during the passivity-breakdown stage. PF improved the mechanical properties of the AS-alloy, especially the indentation modulus and true hardness (statistically significant differences: p = 0.0009 and 0.006, respectively). MSM and MSM/simulating-porcelain firing have been proven trustworthy fabrication methods of Co-Cr-Mo substrates for metal-ceramic prostheses. Moreover, the post-firing cycles improve the mechanical behavior of Co-Cr-Mo, which is vital under the dynamically changing loads in the oral cavity, whereas they do not degrade the corrosion performance.
Topics: Chromium Alloys; Metal Ceramic Alloys; Dental Porcelain; Corrosion; Silicon Dioxide; Surface Properties; Materials Testing
PubMed: 37642767
DOI: 10.1007/s10266-023-00849-2 -
STAR Protocols Sep 2023Plasmonic nanoparticles and nanocrystalline materials have broad applicability in catalysis, optoelectronics, sensing, and sustainability. Below, we detail a robust...
Plasmonic nanoparticles and nanocrystalline materials have broad applicability in catalysis, optoelectronics, sensing, and sustainability. Below, we detail a robust protocol for the synthesis of bimetallic Au-Sn nanoparticles in mild, aqueous conditions. This protocol describes the steps for synthesizing gold nanoparticle seeds, diffusing Sn into the seeds by chemical reduction, and the optical and structural analysis by UV-visible spectroscopy, X-ray diffraction, and electron microscopy. For complete details on the use and execution of this protocol, please refer to Fonseca Guzman et al..
Topics: Tin; Gold; Gold Alloys; Silver; Metal Nanoparticles
PubMed: 37393611
DOI: 10.1016/j.xpro.2023.102410 -
BMC Oral Health Oct 2023The aim of this study was to evaluate the phase composition, phase transformation temperatures, bending property, and cyclic fatigue resistance of different heat-treated...
BACKGROUND
The aim of this study was to evaluate the phase composition, phase transformation temperatures, bending property, and cyclic fatigue resistance of different heat-treated nickel-titanium (NiTi) rotary instruments with the same tip diameter and taper at room (RT; 25 ± 1 °C) and body (BT; 37 ± 1 °C) temperatures.
METHODS
Five heat-treated NiTi rotary instruments, HyFlex EDM (EDM), HyFlex CM (CM), Vortex Blue (VB), RE file CT (RE) and JIZAI, and a non-heat-treated NiTi rotary instrument (Mtwo) with a size 40, 0.04 taper were investigated. Temperature-dependent phase transformation was examined with differential scanning calorimetry (DSC). The bending loads of the instruments at RT and BT were evaluated using a cantilever-bending test. Cyclic fatigue resistance at RT and BT was measured using a dynamic test, during which the instruments were rotated in combination with a 2-mm back-and-forth motion in an artificial curved canal, and the number of cycles to failure (NCF) was determined. The results were analyzed using two-way repeated measures analysis of variance, a simple main effect test, and the Bonferroni test (α = 0.05).
RESULTS
DSC results indicated that EDM and Mtwo were primarily composed of martensite/R-phase and austenite, respectively, while the other heat-treated instruments were composed of a mix of martensite/R-phase and austenite at the tested temperatures. Regardless of the temperature setting, the bending loads of heat-treated instruments were significantly lower than those of Mtwo (p < 0.05). EDM showed the lowest bending loads and highest NCF at both temperatures (p < 0.05). CM, VB, and JIZAI showed significantly higher bending loads at BT than at RT (p < 0.05). The NCF of all the heat-treated instruments, except VB, was lower at BT than at RT (p < 0.05). At BT, the NCF of CM, VB, RE, and JIZAI were not significantly higher than that of Mtwo (p > 0.05).
CONCLUSIONS
Heat-treated NiTi instruments exhibited lower bending loads and higher NCF values than Mtwo. However, this tendency was less pronounced at BT than at RT, especially in the NCF values of instruments with a mixture of martensite/R-phase and austenite phases at the tested temperatures.
Topics: Humans; Hot Temperature; Titanium; Nickel; Body Temperature; Equipment Failure; Dental Alloys; Materials Testing; Dental Instruments; Root Canal Preparation; Stress, Mechanical
PubMed: 37904159
DOI: 10.1186/s12903-023-03550-6 -
Dental Press Journal of Orthodontics 2024This study aimed to compare the insertion torque (IT), flexural strength (FS) and surface alterations between stainless steel (SS-MIs) and titanium alloy (Ti-MIs)... (Comparative Study)
Comparative Study
OBJECTIVE
This study aimed to compare the insertion torque (IT), flexural strength (FS) and surface alterations between stainless steel (SS-MIs) and titanium alloy (Ti-MIs) orthodontic mini-implants.
METHODS
Twenty-four MIs (2 x 10 mm; SS-MIs, n = 12; Ti-MIs, n = 12) were inserted on artificial bone blocks of 20 lb/ft3 (20 PCF) and 40 lb/ft3 (40 PCF) density. The maximum IT was recorded using a digital torque meter. FS was evaluated at 2, 3 and 4 mm-deflection. Surface topography and chemical composition of MIs were assessed by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). General linear and mixed models were used to assess the effect of the MI type, bone density and deflection on the evaluated outcomes.
RESULTS
The IT of Ti-MIs was 1.1 Ncm greater than that obtained for the SS-MIs (p= 0.018). The IT for MIs inserted in 40 PCF test blocks was 5.4 Ncm greater than that for those inserted in 20 PCF test blocks (p < 0.001). SS-MIs inserted in higher density bone (40 PCF) had significantly higher flexural strength than the other groups, at 2 mm (98.7 ± 5.1 Ncm), 3 mm (112.0 ± 3.9 Ncm) and 4 mm (120.0 ± 3.4 Ncm) of deflection (p< 0.001). SEM evidenced fractures in the Ti-MIs. EDS revealed incorporation of 18% of C and 2.06% of O in the loaded SS-MIs, and 3.91% of C in the loaded Ti-MIs.
CONCLUSIONS
Based on the findings of this in vitro study, it seems that SS-MIs offer sufficient stability and exhibit greater mechanical strength, compared to Ti-MIs when inserted into higher density bone.
Topics: Titanium; Torque; Stainless Steel; Surface Properties; Flexural Strength; Orthodontic Anchorage Procedures; Microscopy, Electron, Scanning; Dental Implants; Materials Testing; Dental Alloys; In Vitro Techniques; Spectrometry, X-Ray Emission; Dental Stress Analysis; Humans; Stress, Mechanical; Bone Density
PubMed: 38775601
DOI: 10.1590/2177-6709.29.2.e2423282.oar -
Frontiers in Bioengineering and... 2023In dentistry, the most commonly used implant materials are CP-Titanium Grade 4 and Ti-6Al-4V ELI, possessing comparably high Young's modulus (>100 GPa). In the present...
In dentistry, the most commonly used implant materials are CP-Titanium Grade 4 and Ti-6Al-4V ELI, possessing comparably high Young's modulus (>100 GPa). In the present study, the second-generation titanium alloy Ti-13Nb-13Zr is investigated with respect to the production of advanced dental implant systems. This should be achieved by the fabrication of long semi-finished bars with high strength and sufficient ductility to allow the automated production of small implants at low Young's modulus (<80 GPa) to minimize stress shielding, bone resorption, and gap formation between the bone and implant. In addition, bacterial colonization is to be reduced, and bone adhesion is to be enhanced by adjusting the microstructure. To do so, a dedicated thermo-mechanical treatment for Ti-13Nb-13Zr has been developed. This includes the adaption of equal channel angular swaging, a modern process of severe plastic deformation to continuously manufacture nanostructured materials, to Ti-13Nb-13Zr and short-time recrystallization and ageing treatments. In particular, two-pass equal channel angular swaging at a deformation temperature of 150°C and a counterpressure of 8 MPa has successfully been used to avoid shear band formation during deformation and to produce long Ti-13Nb-13Zr bars of 8 mm diameter. During recrystallization treatment at 700°C for 10 min followed by water quenching, a sub-micron-size primary α-phase in a matrix of α″-phase was developed. Subsequent ageing at 500°C for 1 h leads to martensite decomposition and, thus, to a homogeneously nanostructured microstructure of α- and β-phase with substructures smaller than 200 nm. The resulting mechanical properties, especially the ultimate tensile strength of more than 990 MPa, fulfill the requirements of ASTM F1713 at Young's modulus of 73 GPa. Biological investigations show promising results in reducing bacterial biofilm formation and increased cell proliferation of osteoblasts compared to CP-Titanium Grade 4 and Ti-6Al-4V ELI, especially, if etched surfaces are applied.
PubMed: 37691899
DOI: 10.3389/fbioe.2023.1255947 -
Dental Materials : Official Publication... Mar 2024The Dental Biomaterials Adverse Reaction Unit was initiated by the Norwegian health authorities in 1992 as a response to the public concern regarding the safety of...
OBJECTIVES
The Dental Biomaterials Adverse Reaction Unit was initiated by the Norwegian health authorities in 1992 as a response to the public concern regarding the safety of dental amalgam and other dental materials. In this paper, experiences from the Unit are briefly summarized.
METHODS
The Norwegian health authorities' strategy included four main topics: (i) development of a manufacturer-independent system for monitoring adverse reactions related to dental materials, (ii) funding of a specialty unit for clinical examinations of referred patients, (iii) development of official guidelines for examination and treatment of patients with health complaints attributed to dental materials, and (iv) funding of an experimental treatment project for patients with health complaints attributed to dental amalgam.
RESULTS
From the start, more than 2700 adverse reaction reports were received. In the initial years, amalgam was the most frequent material mentioned in the reports. Reports about polymer-based composite materials have not increased after the prohibition of amalgam in Norway. Clinical examination of referred patients is complex and time consuming, and it is important to consider differential diagnoses. There are methodological challenges associated with the design of experimental treatments used on patients with adverse reactions attributed to dental materials. However, the results from the treatment project indicate lower symptom load after replacement of amalgam with other dental restorative materials.
SIGNIFICANCE
Producer independent adverse reaction reporting can provide valuable information about the safety of these materials and could serve as a complement to the mandatory reporting system described in the European medical device regulations (MDR).
Topics: Humans; Dental Materials; Dental Amalgam; Dental Restoration, Permanent; Norway
PubMed: 38336526
DOI: 10.1016/j.dental.2024.01.004 -
The Japanese Dental Science Review Dec 2023This review covers aspects of orthodontic materials, appliance fabrication and bonding, crossing scientific fields and presenting recent advances in science and... (Review)
Review
This review covers aspects of orthodontic materials, appliance fabrication and bonding, crossing scientific fields and presenting recent advances in science and technology. Its purpose is to familiarize the reader with developments on these issues, indicate possible future applications of such pioneering approaches, and report the current status in orthodontics. The first section of this review covers shape-memory polymer wires, several misconceptions arising from the recent introduction of novel three-dimensional (3D)-printed aligners (mistakenly termed shape-memory polymers only because they present a certain degree of rebound capacity, as most non-stiff alloys or polymers do), frictionless surfaces enabling resistance-less sliding, self-healing materials for effective handling of fractured plastic/ceramic brackets, self-cleaning materials to minimize microbial attachment or plaque build-up on orthodontic appliances, elastomers with reduced force relaxation and extended stretching capacity to address the problem of inadequate force application during wire-engagement in the bracket slot, biomimetic (non-etching mediated) adhesive attachment to surfaces based on the model of the gecko and the mussel, and command-debond adhesives as options for an atraumatic debonding. This review's second section deals with the recent and largely unsubstantiated application of 3D-printed alloys and polymers in orthodontics and aspects of planning, material fabrication, and appliance design.
PubMed: 38022388
DOI: 10.1016/j.jdsr.2023.10.005 -
Dentistry Journal Jul 2023CAD/CAM technologies facilitate using powder CoCr alloys to produce metal-ceramic dental restorations. However, base alloys may induce oxidative stress in the oral...
BACKGROUND
CAD/CAM technologies facilitate using powder CoCr alloys to produce metal-ceramic dental restorations. However, base alloys may induce oxidative stress in the oral cavity due to corrosion and ion release. This study evaluated resistance to corrosion and release of metal ions from 3D printed CoCr dental alloy and their effect on oral oxidative stress.
METHODS
Metal-ceramic crowns with 3D printed copings from CoCr alloy EOS CobaltChrome SP2 (EOS, Germany) were fabricated for 35 patients. Inductively coupled plasma mass spectrometry (ICP-MS) was used for measuring the concentration of Co and Cr ions in non-stimulated saliva before prosthetic treatment (BPT), at 2 h and 7 days after the dental treatment (APT2, APT7, respectively). Open circuit potentials (Eocp) were evaluated at APT2 and APT7. Estimating oral oxidative stress, measurements of 8-isoprostaglandin F2-alpha were conducted using liquid chromatography-tandem mass spectrometry (LC-MS/MS) at stages BPT, APT2, and APT7.
RESULTS
Salivary Co level increased at APT2 and decreased to the initial levels at APT7. No statistical difference was found between the levels of 8-isoPGF2-alpha measured, and between the Eocp measurements at APT2 and APT7.
CONCLUSIONS
The studied alloy showed stable corrosion resistance and the metal ion release did not induce oral oxidative stress.
PubMed: 37504232
DOI: 10.3390/dj11070166