-
Acta Biomaterialia Apr 2020Zinc (Zn) alloys are receiving increasing attention in the field of biodegradable implant materials due to their unique combination of suitable biodegradability and good...
Zinc (Zn) alloys are receiving increasing attention in the field of biodegradable implant materials due to their unique combination of suitable biodegradability and good biological functionalities. However, the currently existing industrial Zn alloys are not necessarily biocompatible, nor sufficiently mechanically strong and wear-resistant. In this study, a Zn-1Cu-0.1Ti alloy is developed with enhanced mechanical strength, corrosion wear property, biocompatibility, and antibacterial ability for biodegradable implant material applications. HR and HR + CR were performed on the as-cast alloy and its microstructure, mechanical properties, frictional and wear behaviors, corrosion resistance, in vitro cytocompatibility, and antibacterial ability were systematically assessed. The microstructures of the Zn-1Cu-0.1Ti alloy after different deformation conditions included a η-Zn phase, a ε-CuZn phase, and an intermetallic phase of TiZn. The HR+CR sample of Zn-1Cu-0.1Ti exhibited a yield strength of 204.2 MPa, an ultimate tensile strength of 249.9 MPa, and an elongation of 75.2%; significantly higher than those of the HR alloy and the AC alloy. The degradation rate in Hanks' solution was 0.029 mm/y for the AC alloy, 0.032 mm/y for the HR+CR alloy, and 0.034 mm/y for the HR alloy. The HR Zn-1Cu-0.1Ti alloy showed the best wear resistance, followed by the AC alloy and the alloy after HR + CR. The extract of the AC Zn-1Cu-0.1Ti alloy showed over 80% cell viability with MC3T3-E1 pre-osteoblast and MG-63 osteosarcoma cells at a concentration of ≤ 25%. The as-cast Zn-1Cu-0.1Ti alloy showed good blood compatibility and antibacterial ability. STATEMENT OF SIGNIFICANCE: This work repots a Zn-1Cu-0.1Ti alloy with enhanced mechanical strength, corrosion wear property, biocompatibility, and antibacterial ability for biodegradable implant applications. Our findings showed that Zn-1Cu-0.1Ti after hot-rolling plus cold-rolling exhibited a yield strength of 204.2 MPa, an ultimate tensile strength of 249.9 MPa, an elongation of 75.2%, and a degradation rate of 0.032 mm/y in Hanks' Solution. The hot-rolled Zn-1Cu-0.1Ti showed the best wear resistance. The extract of the as-cast alloy at a concentration of ≤ 25% showed over 80% cell viability with MC3T3-E1 and MG-63 cells. The Zn-1Cu-0.1Ti alloy showed good hemocompatibility and antibacterial ability.
Topics: Absorbable Implants; Alloys; Animals; Anti-Bacterial Agents; Cell Line, Tumor; Cell Survival; Copper; Hemolysis; Humans; Materials Testing; Mice; Microbial Sensitivity Tests; Staphylococcus aureus; Tensile Strength; Titanium; Zinc
PubMed: 32068137
DOI: 10.1016/j.actbio.2020.02.017 -
Sensors (Basel, Switzerland) Jun 2022This paper mainly focuses on various types of robots driven or actuated by shape memory alloy (SMA) element in the last decade which has created the potential... (Review)
Review
This paper mainly focuses on various types of robots driven or actuated by shape memory alloy (SMA) element in the last decade which has created the potential functionality of SMA in robotics technology, that is classified and discussed. The wide spectrum of increasing use of SMA in the development of robotic systems is due to the increase in the knowledge of handling its functional characteristics such as large actuating force, shape memory effect, and super-elasticity features. These inherent characteristics of SMA can make robotic systems small, flexible, and soft with multi-functions to exhibit different types of moving mechanisms. This article comprehensively investigates three subsections on soft and flexible robots, driving or activating mechanisms, and artificial muscles. Each section provides an insight into literature arranged in chronological order and each piece of literature will be presented with details on its configuration, control, and application.
Topics: Alloys; Mechanical Phenomena; Muscles; Robotics; Shape Memory Alloys
PubMed: 35808360
DOI: 10.3390/s22134860 -
Acta Biomaterialia Jun 2022The metallurgical engineering of bioresorbable zinc (Zn)-based medical alloys would greatly benefit from clarification of the relationships between material properties...
The metallurgical engineering of bioresorbable zinc (Zn)-based medical alloys would greatly benefit from clarification of the relationships between material properties and biological responses. Here we investigate the biocompatibility of three Zn-based silver (Ag)-containing alloys, ranging from binary to quinary alloy systems. Selected binary and quinary Zn-Ag-based alloys underwent solution treatment (ST) to increase the solubility of Ag-rich phases within the Zn bulk matrix, yielding two different microstructures (one without ST and a different one with ST) with the same elemental composition. This experimental design was intended to clarify the relationship between elemental profile/microstructure and biocompatibility for the Zn-Ag system. We found that the quinary alloy system (Zn-4Ag-0.8Cu-0.6Mn-0.15Zr) performed significantly better, in terms of histomorphometry, than any alloy system we have evaluated to date. Furthermore, when solution treated to increase strength and ductility and reduce the fraction of Ag-rich phases, the quinary alloy's biocompatibility further improved. In vitro corrosion testing and metallographic analysis of in vivo implants demonstrated a more uniform mode of corrosion for the solution treated alloy. We conclude that Zn-Ag alloys can be engineered through alloying to substantially reduce neointimal growth. The positive effect on neointimal growth can be further enhanced by dissolving the AgZn precipitates in the Zn matrix to improve the corrosion uniformity. These findings demonstrate that neointimal-forming cells can be regulated by elemental additions and microstructural changes in degradable Zn-based implant materials. STATEMENT OF SIGNIFICANCE: The metallurgical engineering of bioresorbable zinc (Zn)-based medical alloys would greatly benefit from clarification of the relationships between material properties and biological responses. Here, selected binary and quinary Zn-Ag-based alloys underwent solution treatment (ST) to increase the solubility of Ag-rich phases within the Zn bulk matrix, yielding two different microstructures (one without ST and a different one with ST) with the same elemental composition. We found that applying a thermal treatment restores mechanical strength and mitigates the strain rate sensitivity of Zn-Ag alloys by dissolving AgZn precipitates. Ag-rich nano-precipitates in Zn decrease biocompatibility, a phenomenon that can be counteracted by dissolving the AgZn precipitates in the bulk Zn matrix.
Topics: Absorbable Implants; Alloys; Biocompatible Materials; Corrosion; Materials Testing; Stents; Zinc
PubMed: 35367631
DOI: 10.1016/j.actbio.2022.03.047 -
Acta Biomaterialia Oct 2023Zinc (Zn) and its alloys are used in bone-fixation devices as biodegradable bone-implant materials due to their good biosafety, biological function, biodegradability,...
Zinc (Zn) and its alloys are used in bone-fixation devices as biodegradable bone-implant materials due to their good biosafety, biological function, biodegradability, and formability. Unfortunately, the clinical application of pure Zn is hindered by its insufficient mechanical properties and slow degradation rate. In this study, a Zn-5 wt.% lanthanum (Zn-5La) alloy with enhanced mechanical properties, suitable degradation rate, and cytocompatibility was developed through La alloying and hot extrusion. The hot-extruded (HE) Zn-5La alloy showed ultimate tensile strength of 286.3 MPa, tensile yield strength of 139.7 MPa, elongation of 35.7%, compressive yield strength of 262.7 MPa, and microhardness of 109.7 HV. The corrosion resistance of the HE Zn-5La in Hanks' and Dulbecco's modified Eagle medium (DMEM) solutions gradually increased with prolonged immersion time. Further, the HE Zn-5La exhibited an electrochemical corrosion rate of 36.7 μm/y in Hanks' solution and 11.4 μm/y in DMEM solution, and a degradation rate of 49.5 μm/y in Hanks' solution and 30.3 μm/y in DMEM solution, after 30 d of immersion. The corrosion resistance of both HE Zn and Zn-5La in DMEM solution was higher than in Hanks' solution. The 25% concentration extract of the HE Zn-5La showed a cell viability of 106.5%, indicating no cytotoxicity toward MG-63 cells. We recommend the HE Zn-5La alloy as a promising candidate material for biodegradable bone-implant applications. STATEMENT OF SIGNIFICANCE: This work reports the mechanical properties, corrosion and degradation behaviors, in vitro cytocompatibility and antibacterial ability of biodegradable Zn-5La alloy for bone-implant applications. Our findings demonstrate that the hot-extruded (HE) Zn-5La alloy showed an ultimate tensile strength of 286.3 MPa, a yield strength of 139.7 MPa, an elongation of 35.7%, compressive yield strength of 262.7 MPa, and microhardness of 109.7 HV. HE Zn-5La exhibited appropriate degradation rates in Hanks' and DMEM solutions. Furthermore, the HE Zn-5La alloy showed good cytocompatibility toward MG-63 and MC3T3-E1 cells and greater antibacterial ability against S. aureus.
Topics: Materials Testing; Alloys; Corrosion; Zinc; Staphylococcus aureus; Absorbable Implants; Anti-Bacterial Agents; Biocompatible Materials
PubMed: 37541605
DOI: 10.1016/j.actbio.2023.07.061 -
Journal of the Mechanical Behavior of... Sep 2022The corrosion rate of Mg alloys is currently too high for viable resorbable implant applications. One possible solution is to coat the alloy with a hydroxyapatite (HA)...
The corrosion rate of Mg alloys is currently too high for viable resorbable implant applications. One possible solution is to coat the alloy with a hydroxyapatite (HA) layer to slow the corrosion and promote bone growth. As such coatings can be under severe stresses during implant insertion, we present a nano-mechanical and nano-tribological investigation of RF-sputtered HA films on AZ31 Mg alloy substrates. EDX and XRD analysis indicate that as-deposited coatings are amorphous and Ca-deficient whereas rapid thermal annealing results in c-axis orientation and near-stoichiometric composition. Analysis of the nanoindentation data using a thin film model shows that annealing increases the coating's intrinsic hardness (H) and strain at break (H/E) values, from 2.7 GPa to 9.4 GPa and from 0.043 to 0.079, respectively. In addition, despite being rougher, the annealed samples display better wear resistance; a sign that the rapid thermal annealing does not compromise their interfacial strength and that these systems have potential for resorbable bone implant applications.
Topics: Alloys; Coated Materials, Biocompatible; Corrosion; Durapatite; Magnesium; Materials Testing; Surface Properties
PubMed: 35717775
DOI: 10.1016/j.jmbbm.2022.105306 -
Acta Biomaterialia Sep 2022This study systematically investigated the effect of equal channel angular pressing (ECAP) on the microstructure, mechanical, corrosion, nano-tribological properties...
This study systematically investigated the effect of equal channel angular pressing (ECAP) on the microstructure, mechanical, corrosion, nano-tribological properties and biocompatibility of a newly developed β Ti-28Nb-35.4Zr (hereafter denoted TNZ) alloy. Results indicated that ECAP of the β TNZ alloy refined its microstructure by forming ultrafine grains without causing stress-induced phase transformation, leading to formation of a single β phase. The ECAP-processed TNZ alloy exhibited a compressive yield strength of 960 MPa, and high plastic deformation capacity without fracturing under compression loads. Potentiodynamic polarization tests revealed the higher tendency of ECAP-processed TNZ alloys to form passive oxide films on its surface, which exhibited a lower corrosion rate (0.44±0.07 µm/y) in Hanks' balanced salt solution compared to its as-cast counterpart (0.71±0.10 µm/y). Nanotribological testing also revealed higher resistance of the ECAP-processed TNZ alloy to abrasion, wear and scratching, when compared to its as-cast counterpart. Cytocompatibility and cell adhesion assessments of the ECAP-processed TNZ alloys showed a high viability (111%) of human osteoblast-like SaOS2 cells after 7 d of culturing. Moreover, the ECAP-processed TNZ alloy promoted adhesion and spreading of SaOS2 cells, which exhibited growth and proliferation on alloy surfaces. In summary, significantly enhanced mechanical, corrosion, and biological properties of ECAP-processed TNZ alloy advocate its suitability for load-bearing implant applications. STATEMENT OF SIGNIFICANCE: Equal channel angular pressing (ECAP) provides a unique combination of enhanced mechanical and functional properties of materials by optimizing their microstructures and phase transformations. This study investigated the mechanical, nano-tribological, corrosion, and biocompatibility properties of a newly developed β Ti-28Nb-35.4Zr (TNZ) alloy processed via ECAP. Our findings indicated that ECAP of the β TNZ alloy refined its microstructure by forming ultrafine grains without causing stress-induced phase transformation. Compared to its as-cast counterpart, ECAP-processed TNZ exhibited significantly enhanced compressive yield strength, plastic deformation capacity, hardness, wear, and corrosion properties. Moreover, in vitro cytocompatibility and cell adhesion studies revealed high cellular viabilities, growth and proliferation of osteoblast-like SaOS2 cells on the ECAP-processed TNZ alloy.
Topics: Alloys; Biocompatible Materials; Compressive Strength; Corrosion; Humans; Materials Testing; Plastics; Titanium
PubMed: 35817341
DOI: 10.1016/j.actbio.2022.07.005 -
Journal of Biomaterials Applications Apr 2022Corrosion resistant and biocompatible AZ31 magnesium alloy surfaces were successfully prepared by ultrasonic cold forging and subsequent micro-arc oxidation. The...
Corrosion resistant and biocompatible AZ31 magnesium alloy surfaces were successfully prepared by ultrasonic cold forging and subsequent micro-arc oxidation. The properties of these ultrasonic cold forging pretreated (UCFT)AZ31 magnesium alloy surfaces containing Sr-Ca-P micro-arc oxide coating (MAO/UCFT/AZ31) were studied. Results showed that surface grain refinement of AZ31 Mg alloy in the depth of 400 μm owing to the ultrasonic cold forging pretreatment was verified, and which provides more discharge channels for subsequent micro-arc oxidation. Comparing with the AZ31 magnesium alloy (AZ31) and ultrasonic cold forging technology treated AZ31 magnesium alloy samples (UCFT/AZ31), the corrosion resistance of MAO/UCFT/AZ31 significantly improved, which is also supported by the immersion experiments and electrochemical tests in simulated body fluid. Meanwhile, the MAO/UCFT/AZ31 samples also had excellent cytocompatibility as well as MAO/AZ31 samples. These results may beneficial to the developing of biodegradable medical materials in future.
Topics: Alloys; Coated Materials, Biocompatible; Corrosion; Magnesium; Monoamine Oxidase; Ultrasonics
PubMed: 35156449
DOI: 10.1177/08853282211046776 -
Biomaterials Advances Feb 2022In order to avoid the toxic and side effects on human body of long-term dissolution of metal ions from antibacterial titanium alloys, Au element with non-toxicity and...
In order to avoid the toxic and side effects on human body of long-term dissolution of metal ions from antibacterial titanium alloys, Au element with non-toxicity and non-side effect was selected as the alloying element to prepare a new Ti-Au alloy with strong antibacterial property. We produced Ti-Au(S) sintered alloy by powder metallurgy and Ti-Au ingot alloy by ingot metallurgy, and investigated the influence of the secondary phase on the relative antimicrobial properties and antibacterial mechanism in this work. The results indicated that the aged Ti-Au(T6) alloy and Ti-Au(S) sintered alloy exhibited strong antibacterial rate against S. aureus due to the formation of TiAu phases. In vitro cell culture (MC3T3 cells) experiments showed that Ti-Au alloys had good cytocompatibility and osteogenic properties. The following viewpoints of antibacterial mechanism are that the TiAu destroyed the ROS homeostasis of bacteria, causing oxidative stress in bacterial cells and preventing from the biofilms formation.
Topics: Aged; Alloys; Anti-Bacterial Agents; Corrosion; Humans; Staphylococcus aureus; Titanium
PubMed: 35034820
DOI: 10.1016/j.msec.2022.112653 -
Journal of Prosthodontics : Official... Aug 2022To review the most up to date scientific evidence concerning the technical implications, soft tissue biocompatibility, and clinical applications derived from the use of... (Review)
Review
PURPOSE
To review the most up to date scientific evidence concerning the technical implications, soft tissue biocompatibility, and clinical applications derived from the use of titanium nitride hard thin film coatings on titanium alloy implant abutments.
MATERIALS AND METHODS
A review was performed to answer the following focused question: "What is the clinical reliability of nitride coated titanium alloy abutments?". A MEDLINE search between 1980 and 2021 was performed for investigations pertaining to the clinical use of nitride coated titanium alloy implant abutments (TiN) in case reports, case series, and short- and long-term non/randomized controlled clinical trials. Literature analysis led to addition evaluation of research related to the technical and biological aspects, as well as the physicochemical characteristics of TiN hard thin film coatings and their impact on titanium abutment biocompatibility, mechanical properties, macroscopic surface topography, and optical properties. Therefore, preclinical data from biomechanical and in vitro investigations were also considered as inclusion criteria.
RESULTS
The limited number of clinical investigations published made a systematic review and meta-analysis not possible, therefore a narrative review was conducted. TiN coatings have been applied to dental materials and instruments to improve their clinical longevity. Implant abutments are coated with titanium nitride to mask the titanium oxide surface and enhance its surface characteristics providing the TiN abutment surface with a low friction coefficient and a very high chemical inertness. TiN coating is suggested to reduce early bacterial colonization and biofilm formation and enhance fibroblast cell proliferation, attachment and adhesion when compared to Ti controls. Additionally, studies indicate that hard thin film coatings enhance the mechanical properties (hardness and wear resistance) of titanium alloy and appears as a yellow color when deposited on the titanium alloy substrate. To date, clinical investigations show that nitride coated titanium abutments provide promising short-term clinical outcomes.
CONCLUSIONS
Published research on nitride-coated abutments is still limited, however, the available biomedical research, mechanical engineering tests, in vitro investigations, and short-term clinical trials have, to date, reported promising mechanical, biological, and esthetic outcomes.
Topics: Alloys; Dental Abutments; Dental Implants; Esthetics, Dental; Reproducibility of Results; Surface Properties; Titanium
PubMed: 34731520
DOI: 10.1111/jopr.13446 -
Magnetic Resonance Imaging Jan 2022Magnetic resonance imaging (MRI) devices are frequently used in image-based diagnosis. In the case of large artifacts, which are generated in magnetic resonance (MR)...
PURPOSE
Magnetic resonance imaging (MRI) devices are frequently used in image-based diagnosis. In the case of large artifacts, which are generated in magnetic resonance (MR) images when magnetic materials, such as metals, are present in the body, these devices are less useful. This study aimed to develop a dual-phase Au-Pt alloy that does not generate artifacts in MR images and has high workability to prepare medical devices.
MATERIALS AND METHODS
A processing method to produce a dual-phase Au-Pt alloy was established, and the magnetic susceptibility and artifacts of different alloy compositions were determined using a SQUID (superconducting quantum interference device) flux meter and a 1.5 T-MRI system. The crystallographic phases of the prepared alloy samples were identified using X-ray diffraction. Sample cross-sections were observed using a metallurgical microscope. Furthermore, a thinning test was conducted to examine alloy workability.
RESULTS
Dual-phase Au-Pt alloys Au70Pt30 and Au67Pt33-the former heat-treated at 800 and 850 °C and the latter heat-treated at 900 °C-generated minimal artifacts when imaged in a 1.5 T-MRI system. Their volume magnetic susceptibility increased as the heat-treatment temperature decreased. The alloy surfaces were observed to be uniform. Moreover, the workability of the dual-phase alloy was considerably better than that of the single-phase alloy.
CONCLUSION
Volume magnetic susceptibility could be controlled by changing the composition and processing temperature of the Au-Pt alloys. Dual-phase Au-Pt alloys those do not generate magnetic susceptibility artifacts in MRI images and have good workability could be prepared. The alloys are expected to be used in the preparation of various implantable medical devices.
Topics: Alloys; Artifacts; Magnetic Resonance Imaging; Magnetics; Metals
PubMed: 34653577
DOI: 10.1016/j.mri.2021.10.002