-
Journal of Environmental Sciences... Jun 2021Sodium hypochlorite (NaClO) is a commonly applied cleaning agent for ultrafiltration membranes in water and wastewater treatment. Long-term exposure to NaClO might...
Sodium hypochlorite (NaClO) is a commonly applied cleaning agent for ultrafiltration membranes in water and wastewater treatment. Long-term exposure to NaClO might change the properties and performance of polymeric membranes, and ultimately shorten membrane lifespan. Active species in NaClO solution vary with solution pH, and the aging effects can change depending on the membrane material. In this study, the aging of polyvinylidene fluoride (PVDF) and polyethersulfone (PES) membranes by NaClO at pH 3-11 was investigated by examining variations in chemical composition, surface charge, surface morphology, mechanical strength, permeability, and retention ability. Polyvinyl pyrrolidone (PVP), which was blended in both membranes, was oxidized and dislodged due to NaClO aging at all investigated pH values, but the oxidation products and dislodgement ratio of PVP varied with solution pH. For the PVDF membrane, NaClO aging at pH 3-11 caused a moderate increase in permeability and decreased retention due to the oxidation and release of PVP. The tensile strength decreased only at pH 11 because of the defluorination of PVDF molecules. For the PES membrane, NaClO aging at all investigated pH resulted in chain scission of PES molecules, which was favored at pH 7 and 9, potentially due to the formation of free radicals. Therefore, a decrease in tensile strength and retention ability, as well as an increase in permeability, occurred in the PES membrane for NaClO aging at pH 3-11. Overall, the results can provide a basis for selecting chemical cleaning conditions for PVDF and PES membranes.
Topics: Hydrogen-Ion Concentration; Membranes, Artificial; Polymers; Polyvinyls; Sodium Hypochlorite; Sulfones; Ultrafiltration
PubMed: 33985746
DOI: 10.1016/j.jes.2020.12.020 -
Journal of the Mechanical Behavior of... Feb 2022Polyvinyl alcohol hydrogel (PVA-H) has been widely used in clinical transplantation because of its high water content, good biocompatibility and mechanical properties....
Polyvinyl alcohol hydrogel (PVA-H) has been widely used in clinical transplantation because of its high water content, good biocompatibility and mechanical properties. However, PVA-H have some problems, such as low elongation at break, low fatigue resistance and high friction coefficient, which hinders its application in clinic. In this paper, a novel high-performance PVA hydrogel enhanced by chemical double crosslinking (CDC) method had been synthesized. The influences of chemical crosslinking agent concentration on mechanical properties, friction properties and fatigue properties of materials were systematically investigated, in order to meet the clinical application of artificial meniscus, artificial cartilage, nucleus pulposus and so on. As a result, due to the introduction of chemical bonds, CDC hydrogels have over 600% elongation at break, modulus loss after fatigue test was reduced by 42%, average coefficient during friction was reduced to 0.048, and biocompatibility performance was excellent. The PVA hydrogel enhanced by CDC method provides a new concept for us to prepare high-performance PVA hydrogel and a promising material to replace cartilage, meniscus, nucleus pulposus and other tissues.
Topics: Cartilage; Friction; Hydrogels; Polyvinyl Alcohol
PubMed: 34861520
DOI: 10.1016/j.jmbbm.2021.105009 -
Journal of the Mechanical Behavior of... Dec 2020Polyvinyl alcohol is used to 3D print (fused deposition modelling) sampling matrices for bacterial detection. A specific configuration was designed using Computer-Aided...
Polyvinyl alcohol is used to 3D print (fused deposition modelling) sampling matrices for bacterial detection. A specific configuration was designed using Computer-Aided Design software. The mechanical properties of the printed samples were studied using uniaxial tensile testing, and compared to those of the original Polyvinyl alcohol filament, with and without heat treatment. The effects of different factors such as UV treatment, printing speed, infill density and printing direction on the mechanical properties of the printed samples including strength, strain and modulus of elasticity were studied. The results show that the effect of the fused deposition modelling process on the mechanical properties of the printed Polyvinyl alcohol cannot be explained by its exposure to heat. UV treatment reduced the strength, characteristic strains and Young's modulus. It makes Polyvinyl alcohol samples brittle. The effects of printing speed and the infill density on the mechanical properties of printed samples can be no linear. An unexpected relation between printing direction and mechanical properties was demonstrated by the studied specimens that needs further theoretical understanding. There is a huge scatter in strength of PVA samples compared with typical engineering materials, and in the fracture strain of original PVA filament, the 3D printing process can reduce the scatter but only by a limited extent. To summarise, there is a sophisticated relation between printing parameters and the mechanical properties of the printed Polyvinyl alcohol.
Topics: Elastic Modulus; Polyvinyl Alcohol; Printing, Three-Dimensional
PubMed: 32942228
DOI: 10.1016/j.jmbbm.2020.104066 -
The Journal of Prosthetic Dentistry May 2022Redesigned mixing tips, promising less impression material waste, have been marketed. However, whether their use adversely affects the dimensional stability and detail...
STATEMENT OF PROBLEM
Redesigned mixing tips, promising less impression material waste, have been marketed. However, whether their use adversely affects the dimensional stability and detail reproduction of the impression material is unclear.
PURPOSE
The purpose of this in vitro study was to evaluate the dimensional stability, detail reproduction, and material waste of different polyvinyl siloxane impression materials (regular and light-body) mixed with 2 different mixing tips (MIXPAC T-Mixer mixing tip and MIXPAC helical mixing tip).
MATERIAL AND METHODS
Six different polyvinyl siloxane impression materials were used in 2 different consistencies: Virtual Monophase and Virtual Light Body (Ivoclar Vivadent AG), Express XT Regular and Express XT Light Body (3M ESPE), and Panasil initial contact Regular and Panasil initial contact Light (Kettenbach). The polyvinyl siloxane impression materials were mixed with 2 different mixing tips: conventional helical and T-Mixer (n=10). The specimens were prepared in a metal matrix as per specification #19 of the American National Standards Institute/American Dental Association (ANSI/ADA) and International Organization for Standardization (ISO) 4823:2015. The materials were mixed with both mixing tips as per the manufacturer's instructions, inserted into a perforated custom tray on the matrix, and allowed to polymerize completely. The dimensional stability was calculated based on the measurement of the reproduction of lines engraved in the metal matrix. Detail reproduction was evaluated through analysis of continuity and reproducibility of those lines, immediately, 7 days, and 14 days after polymerization. Material waste was assessed by the difference between the initial (before mixing) and final weight (after complete polymerization) of both mixing tips. The data on dimensional stability and detail reproduction among the materials were submitted to the Kruskal-Wallis test, followed by the Student-Newman-Keuls test (α=.05). Comparison between the mixing tips was carried out with the Mann-Whitney test (α=.05), while the comparison among the periods of analysis (immediate, 7 days, and 14 days) was carried out with the Friedman test (α=.05). The data on material waste between the mixing tips were submitted to 1-way ANOVA, followed by the Tukey honestly significant difference tests (α=.05).
RESULTS
The T-Mixer mixing tip resulted in reduced material waste. For dimensional stability, Virtual Light mixed with T-Mixer resulted in lower dimensional change (0.53 ±0.58%) compared with the helical mixing tip (1.09 ±0.43%). Among the materials, Panasil Light presented higher values of dimensional change at immediate and 7-day analysis when mixed with T-Mixer tip with a statistical difference compared with Express Light, Virtual Light, and Panasil Regular (P<.05). In general, both mixing tips provided similar results in all periods of analysis (P>.05) for qualitative analysis of detail reproduction.
CONCLUSIONS
The T-Mixer tip resulted in less material waste compared with the helical mixing tip. In general, light-body materials showed higher dimensional stability when the T-Mixer tip was used compared with the conventional tip. In general, reduced detail reproduction was observed after periods longer than 7 days after impression making.
Topics: Dental Impression Materials; Dental Impression Technique; Humans; Materials Testing; Polyvinyls; Reproducibility of Results; Reproduction; Siloxanes
PubMed: 33454110
DOI: 10.1016/j.prosdent.2020.11.024 -
International Journal of Biological... Dec 2023The discharge of dye wastewater resulting from rapid industrial development has become a serious environmental concern. Therefore, there is a pressing need to develop...
The discharge of dye wastewater resulting from rapid industrial development has become a serious environmental concern. Therefore, there is a pressing need to develop efficient methods and technologies for the removal of dye pollutants. This study introduced a double network hydrogel, with varying carboxymethyl chitosan (CMCS) contents and polyvinyl alcohol (PVA), employing a combination of freeze- thawing and calcium chloride cross-linking. The investigation focused on the rheological properties of the hydrogels and their removal ability of acidic blue 93 (AB). The results showed that the strength and viscoelastic modulus of composite hydrogels were positively correlated with the CMCS content, and all composite hydrogels exhibited the typical weak strain overshoot behavior. The pore size of the gel initially decreased and then increased, with the densest pores observed at 4 wt% CMCS, showing the optimal removal ability for AB. The adsorption process followed pseudo second-order kinetic model, dominated by external diffusion, and exhibited inhomogeneous multilayer adsorption. This study unveils the potential of CMCS/PVA gels as adsorbents, offering inspirations for the design and development of polyvinyl alcohol-based gels for applications in the food industry.
Topics: Chitosan; Calcium Chloride; Polyvinyl Alcohol; Adsorption; Hydrogels
PubMed: 37709214
DOI: 10.1016/j.ijbiomac.2023.126897 -
ACS Applied Materials & Interfaces Jan 2023Piezoelectric sensors are widely used in wearable devices to mimic the functions of human skin. However, it is considerably challenging to develop soft piezoelectric...
Piezoelectric sensors are widely used in wearable devices to mimic the functions of human skin. However, it is considerably challenging to develop soft piezoelectric materials that can exhibit high sensitivity, stretchability, super elasticity, and suitable modulus. In this study, a soft skin-like piezoelectric polymer elastomer composed of poly(vinylidene fluoride) (PVDF) and a novel elastic substrate polyacrylonitrile is prepared by combining the radical polymerization and freeze-drying processes. Dipole-dipole interaction results in the phase transition of PVDF (α phase to β phase), which enhances the electrical and mechanical performances. Thus, we achieve a high piezoelectric coefficient ( = 63 pC/N), good stretchability (211.3-259.3%), super compressibility (subjected to 99% compression strain without cracking), and super elasticity (100% recovery after extreme compression) simultaneously for the elastomer. The soft composite elastomer produces excellent electrical signal output ( = 253 mV) and responds rapidly (15 ms) to stress-induced polarization effects. In addition, the elastomer-based sensor accurately detects various physiological signals such as gestures, throat vibrations, and pulse waves. The developed elastomers exhibit excellent mechanical properties and high sensitivity, which helps facilitate their application as artificial electronic skin to sense subtle external pressure in real time.
Topics: Humans; Elastomers; Polymers; Wearable Electronic Devices; Polyvinyls
PubMed: 36571179
DOI: 10.1021/acsami.2c19654 -
Molecules (Basel, Switzerland) Aug 2022A sensitive and selective fluorescence-detection platform based on carbon quantum dots (CQDs) was designed and developed for the determination of methotrexate (MTX), for...
OBJECTIVE
A sensitive and selective fluorescence-detection platform based on carbon quantum dots (CQDs) was designed and developed for the determination of methotrexate (MTX), for the purpose of minimizing the possible toxic threat of MTX in clinics.
METHODS
The approach was prepared for the first time by a simple, hydrothermal method, making the synthesis and modification processes realized in one step using polyethyleneimine (PEI), and the proposed PEI-CQDs were obtained with high fluorescence quantum yield (38%).
RESULTS
MTX was found highly responsive and effective in quenching the fluorescence of the PEI-CQDs, due to a suggested fluorescence resonance energy transfer mechanism or inner-filter effect. The linear range of MTX was between 1 and 600 μmol/L under optimum conditions, with a detection limit (LOD) as low as 0.33 μmol/L. Furthermore, the fluorescent method was established for the MTX assay, and satisfactory results were acquired in real-sample determination. The average labeled quantity was 98.2%, and the average added standard recovery was 100.9%.
CONCLUSIONS
The proposed PEI-CQDs showed a remarkable potential for broad applications in biological molecule determination and environmental analysis.
Topics: Carbon; Fluorescent Dyes; Limit of Detection; Methotrexate; Polyethyleneimine; Polyvinyls; Quantum Dots; Spectrometry, Fluorescence
PubMed: 36014493
DOI: 10.3390/molecules27165254 -
BioMed Research International 2022To determine the hardness and Young's moduli of both commercial and experimental vinyl poly siloxane (VPS). (Comparative Study)
Comparative Study
PURPOSE
To determine the hardness and Young's moduli of both commercial and experimental vinyl poly siloxane (VPS).
METHODS
The purpose of this study was to develop a medium-bodied experimental (Exp-I, II, III, IV, and V) VPS impression materials and to analyse their effects on hardness and Young's modulus and compare them with three commercial VPS materials (Aquasil, Elite, and Extrude) using Shore A hardness tester. Measurements were recorded after 1, 24, 72, and 168 hours of mixing. The results were analysed with one-way ANOVA and post hoc Tukey's test using the SPSS PASW statistical 22 software.
RESULTS
Commercial and experimental vinyl polysiloxane exhibited higher Shore A hardness values with time (i.e., 1 hour after mixing, 24 hours after mixing, 72 hours after mixing, and 1 week after mixing). All Comml and Exp VPS demonstrated a significant increase (ANOVA, < 0.05) in hardness at increasing time points. Generally, all commercial VPS exhibited significantly higher values for Shore A hardness compared to all Exp formulations. For commercial products, Elt M presented significantly highest values at all-time points followed by Aq M then Extr M. Exp-I was significantly harder than all other Exp VPS at all-time points. Young's modulus values were directly related to Shore A hardness; materials with higher Shore A hardness values had higher Young's moduli.
CONCLUSION
Continued polymerisation of elastomeric impression materials results in increased hardness over time. Hardness, Young's moduli, and rigidity of the set commercial and experimental VPS materials were within the required limits. Shore A hardness and Young's moduli were directly proportional to each other, and commercial and experimental materials had enough rigidity to contain the stone during pouring.
Topics: Dental Impression Materials; Elastic Modulus; Hardness; Materials Testing; Polyvinyls; Silicone Elastomers; Siloxanes
PubMed: 35187157
DOI: 10.1155/2022/1703869 -
Journal of the Mechanical Behavior of... Dec 2023The polymeric nanofiber may interact and control certain regeneration processes at the molecular level to repair damaged tissues. This research focuses on the...
The polymeric nanofiber may interact and control certain regeneration processes at the molecular level to repair damaged tissues. This research focuses on the development of characterization and antibacterial capabilities of polyvinyl alcohol (PVA)/chitosan (CS) nanofibres containing fucoidan (FUC) for tissue engineering as a skin tissue substitute. A control group consisting of 13% PVA/(0.1)% CS nanofiber was prepared. To confer antibacterial properties to the nanofiber, 10, 20, and 30 mg of FUC were incorporated into this control group. The scanning electron microscope (SEM) proved the homogeneous and beadless structures of the nanofibers. The antibacterial activity of the 13% PVA/(0.1)% CS/(10, 20, 30) FUC was tested against the S.aureus and E.coli and the results showed that with FUC addition, the antibacterial activities of the nanofibers increased. The biocompatibility test was performed with a fibroblast cell line for 1, 3, and 7 days of incubation and the results demonstrated that FUC addition enhanced the bioactivity of the 13% PVA/(0.1)% CS nanofibers. In addition, the biocompatibility results showed that 13% PVA/(0.1)% CS/10 FUC had the highest viability value for all incubation periods compared to the others. In addition, the tensile test results showed that; the maximum tensile strength value was observed for 13% PVA/(0.1)% CS/10 FUC nanofibers.
Topics: Chitosan; Polyvinyl Alcohol; Nanofibers; Polyvinyls; Tissue Engineering; Anti-Bacterial Agents; Staphylococcus aureus; Escherichia coli
PubMed: 37832172
DOI: 10.1016/j.jmbbm.2023.106163 -
International Journal of Biological... May 2023Chronic wounds are slow to recover. During treatment, the dressing needs to be removed to check the recovery status, a process that often results in wound tears....
Chronic wounds are slow to recover. During treatment, the dressing needs to be removed to check the recovery status, a process that often results in wound tears. Traditional dressings lack stretching and flexing properties and are not suitable using on wounds in joints, which require movement from time to time. In this study, we present a stretchable, flexible and breathable bandage consisting of three layers, including Mxene coating on the top, the polylactic acid/polyvinyl pyrrolidone (PLA/PVP) layer designed as Kirigami in the middle, and the f-sensor at the bottom. By the way, the f-sensor is in contact with the wound sensing real-time microenvironmental changes due to infection. When the infection intensifies, the Mxene coating at the top is utilized to enable anti-infection treatment. And Kirigami structure of PLA/PVP ensures that this bandage has stretchability, bendability, and breathability. The stretch of the smart bandage increases to 831 % compared to the original structure, and the modulus reduces to 0.04 %, which adapts extremely well to the movement of the joints and relieves the pressure on the wound. This monitoring-treatment closed-loop working mode, eliminating the need to remove dressings and avoid tissue tearing, shows a promising capability in the field of surgical wound care.
Topics: Povidone; Polyvinyls; Bandages; Polyesters
PubMed: 36990399
DOI: 10.1016/j.ijbiomac.2023.124204