-
Frontiers in Veterinary Science 2022Water is one of the primary vectors for African swine fever virus (ASFV) transmission among swine herds. However, the low concentrations of ASFV in water represent a...
Water is one of the primary vectors for African swine fever virus (ASFV) transmission among swine herds. However, the low concentrations of ASFV in water represent a challenge for the detection of the virus by conventional PCR methods, and enrichment of the virus would increase the test sensitivity. In this study, aiming to enrich ASFV in water quickly and efficiently, a rapid and efficient water-borne virus enrichment system (MDEF, modified diatomaceous earth by ferric hydroxide colloid) was used to enrich ASFV in water. After enrichment by MDEF, conventional real-time PCR (qPCR) was used for ASFV detection. ASFV were inactivated and diluted in 10 L of water, of which 4 mL were collected after 60 min treatment using the MDEF system. Two thousand five hundred times reduction of the sample volume was achieved after enrichment. A high adsorption rate of about 99.99 (±0.01)% and a high recovery rate of 64.01 (±10.20)% to 179.65 (±25.53)% was achieved by using 1g modified diatomaceous earth for 10 L ASFV contaminated water. The limit of qPCR detection of ASFV decreased to 1 × 10 GU ml (genomic units per milliliter) from 1 × 10 GU ml after concentrating the spiked water from 10 L to 4 ml. Preliminary application of MDEF allowed successful detection of African swine fever virus (ASFV), porcine circovirus type 2 (PCV2), and pseudorabies virus (PRV) in sewage. Thus, the combination of modified diatomaceous earth and real-time PCR is a promising strategy for the detection of viruses in water.
PubMed: 36619955
DOI: 10.3389/fvets.2022.1045190 -
Molecules (Basel, Switzerland) Mar 2020The development of novel materials and approaches for effective energy consumption and the employment of renewable energy sources is one of the current trends in modern... (Review)
Review
The development of novel materials and approaches for effective energy consumption and the employment of renewable energy sources is one of the current trends in modern material science. With this respect, the number of researches is focused on the effective harvesting and storage of solar energy for various applications. Phase change materials (PCMs) are known to be able to store thermal energy of the sunlight due to adsorption and release of latent heat through reversible phase transitions. Therefore, PCMs are promising as functional additives to construction materials and paints for advanced thermoregulation in building and industry. However, bare PCMs have limited practical applications. Organic PCMs like paraffins suffer from material leakage when undergoing in a liquid state while inorganic ones like salt hydrates lack long-term stability after multiple phase transitions. To avoid this, the loading of PCMs in porous matrices are intensively studied along with the thermal properties of the resulted composites. The loading of PCMs in microcontainers of natural porous or layered clay materials appears as a simple and cost-effective method of encapsulation significantly improving the shape and cyclic stability of PCMs. Additionally, the inclusion of functional clay containers into construction materials allows for improving their mechanical and flame-retardant properties. This article summarizes the recent progress in the preparation of composites based on PCM-loaded clay microcontainers along with their future perspectives as functional additives in thermo-regulating materials.
Topics: Algorithms; Clay; Diatomaceous Earth; Geothermal Energy; Hot Temperature; Kaolin; Magnesium Silicates; Models, Molecular; Models, Theoretical; Phase Transition; Porosity; Thermal Conductivity; Thermodynamics
PubMed: 32225028
DOI: 10.3390/molecules25071504 -
Analytical and Bioanalytical Chemistry Mar 2022Herein, we developed an ultra-fast and visual single-tube nucleic acid detection approach, which combined the advantages of self-settling characteristics of...
Herein, we developed an ultra-fast and visual single-tube nucleic acid detection approach, which combined the advantages of self-settling characteristics of chitosan-functionalized diatomaceous earth (CDE) and accelerated PCR (AC-PCR). DNA was rapidly extracted by CDE within 3 min for the next nucleic acid amplification based on the nucleic acid attached on the chitosan in pH = 5.0. Under the action of gravity, the DNA-enriched CDE self-sediments to the bottom of the tube could be directly used for AC-PCR to achieve single-tube extraction and amplification. Our method detected Salmonella culture fluids with a detection limit of 1 CFU/mL, which was 100-fold more sensitive than conventional method that have not undergone nucleic acid enrichment. Furthermore, it also displayed high specificity and sensitivity for a variety of spiked samples. The entire process could be completed within 17 min in a single tube, and in particular, the result was visualized by the naked eyes. Overall, it is an all-in-one detection strategy without the requirement of redundant procedure, which greatly improved the detection efficiency, and saved the time and the cost. With these advantages, the approach will supply a promising tool in the field of point-of-care testing for Salmonella and other foodborne pathogens.
Topics: DNA; Nucleic Acid Amplification Techniques; Nucleic Acids; Polymerase Chain Reaction; Salmonella; Sensitivity and Specificity
PubMed: 35079852
DOI: 10.1007/s00216-022-03904-z -
Materials (Basel, Switzerland) Feb 2023The clarity of the beer is essential to its marketability and good consumer approval. Moreover, the beer filtration aims to remove the unwanted constituents that cause...
The clarity of the beer is essential to its marketability and good consumer approval. Moreover, the beer filtration aims to remove the unwanted constituents that cause beer haze formation. Natural zeolite, an inexpensive and widespread material, was tested as a substitute filter media for diatomaceous earth in removing the haze constituents in beer. The zeolitic tuff samples were collected from two quarries in Northern Romania: Chilioara, in which the zeolitic tuff has a clinoptilolite content of about 65%, and the Valea Pomilor quarry, containing zeolitic tuff with a clinoptilolite content of about 40%. Two-grain sizes, <40 and <100 µm, from each quarry were prepared and thermally treated at 450 °C in order to improve their adsorption properties and remove organic compounds and for physico-chemical characterization. The prepared zeolites were used for beer filtration in different mixtures with commercial filter aids (DIF BO and CBL3) in laboratory-scale experiments, and the filtered beer was characterized in terms of pH, turbidity, color, taste, flavor, and concentrations of the major and trace elements. The results showed that the taste, flavor, and pH of the filtered beer were generally not affected by filtration, while turbidity and color decreased with an increase in the zeolite content used in the filtration. The concentrations of Na and Mg in the beer were not significantly altered by filtration; Ca and K slowly increased, while Cd and Co were below the limits of quantification. Our results show that natural zeolites are promising aids for beer filtration and can be readily substituted for diatomaceous earth without significant changes in brewery industry process equipment and protocols for preparation.
PubMed: 36903029
DOI: 10.3390/ma16051914 -
RSC Advances Feb 2022A chitosan (a glucosamine polysaccharide)-diatomaceous earth hybrid was studied for the adsorption of 4,4'-dichloro-diphenyl-trichloroethane (4,4'-DDT), a persistent...
Tapping the potential of a glucosamine polysaccharide-diatomaceous earth hybrid adsorbent in the solid phase extraction of a persistent organic pollutant and toxic pesticide 4,4'-DDT from water.
A chitosan (a glucosamine polysaccharide)-diatomaceous earth hybrid was studied for the adsorption of 4,4'-dichloro-diphenyl-trichloroethane (4,4'-DDT), a persistent organic pollutant and organochlorine pesticide compound from water. The diverse adsorption process parameters were studied and the modified adsorbent was characterized through XRD, SEM-EDX, FT-IR, XRF, BET and TGA analysis. The concentration of 4,4'-DDT was measured using gas chromatography-tandem mass spectrometry (GC-MS/MS) by adopting a validated analytical procedure. The Langmuir and Freundlich isotherms ascertained the adsorption capacity. The optimum pH and temperature for 4,4'-DDT adsorption were found to be between 5.0 and 7.0 and 20 and 30 °C respectively. Thermodynamic parameters confirmed that the adsorption of DDT on chitosan modified with diatomaceous earth was an exothermic process. The data obtained from kinetics and intra-particle diffusion showed that the composite material is able to sequester 4,4'-DDT and this is reflected in the Langmuir adsorption capacity of 0.968 mg g. The adsorbed 4,4'-DDT was successfully eluted with ethyl acetate and recycling studies showed that the modified chitosan can be used for three cycles with significant adsorption performance and this adsorbent proved its efficacy in removing 4,4'-DDT from farm water.
PubMed: 35425579
DOI: 10.1039/d1ra07868b -
Materials (Basel, Switzerland) Oct 2022The development of geopolymer building composites at a lower cost with a smaller carbon footprint may lessen the growing concerns about global warming brought on by... (Review)
Review
The development of geopolymer building composites at a lower cost with a smaller carbon footprint may lessen the growing concerns about global warming brought on by emissions of a critical greenhouse gas (CO) paired with the high production costs in the cement sector. Diatomaceous earth, commonly used as an admixture or partial replacement of cement owing to its most effective pozzolanic properties, has been investigated as a precursor in geopolymer concrete development. Several studies have been examined to develop a greater understanding of its characterization, inclusion status, and impacts on the performance aspects of concrete. The literature review showed that using diatomaceous earth is one of the effective ways to create sustainable, insulating, lightweight building materials while minimizing the harmful economic and environmental effects of industrial solid wastes. However, since most studies have focused on its integration as a partial cement substitute or a replacement for fine aggregate, further research on diatomaceous earth-based clinker-free concrete is required. A lack of research on geopolymer concrete's reinforcement with either natural or synthetic fibers, or a combination of the two, was also discovered. This review also showed that there has been remarkably little effort made towards theoretical property correlation modeling for predicting concrete performance. It is anticipated that the detailed overview presented herein will guide potential researchers in defining their future paths in the study area.
PubMed: 36295195
DOI: 10.3390/ma15207130 -
Journal of Pesticide Science Aug 2022The common pistachio psylla, , is a serious global pest menacing pistachio orchards. Considering the dangers of using excessive chemical pesticides, it seems that using...
The common pistachio psylla, , is a serious global pest menacing pistachio orchards. Considering the dangers of using excessive chemical pesticides, it seems that using natural insecticides such as diatomaceous earth is a suitable way to lower the residual amount of highly hazardous pesticides. In this study, the effects of diatomaceous earth with different additives, including dipotassium hydrogen phosphate, polyurethane glue as a wood adhesive, and potassium silicate, were investigated in several concentrations over two years in orchard conditions. Although all treatments showed significant effects, the most effective treatments were (diatomaceous earth+dipotassium hydrogen phosphate) and (diatomaceous earth+polyurethane glue). Therefore, the use of diatomaceous earth combined with the additive materials mentioned can potentially be a safe method for the integrated management of the common pistachio psylla.
PubMed: 36479454
DOI: 10.1584/jpestics.D22-019 -
Polymers Aug 2022Amorphous diatomite was used as a filler for a thermoplastic polymer of polyamide 11 obtained from natural sources. The diatomite particles of different sizes were...
Amorphous diatomite was used as a filler for a thermoplastic polymer of polyamide 11 obtained from natural sources. The diatomite particles of different sizes were previously fractionated by sedimentation to obtain powders with varying particle size distribution, including powders with or without frustule particles, crushed, uncrushed or agglomerated. Biocomposites containing 2.5, 5, 10 and 20% filler were tested for their mechanical properties, including tensile strength, flexural strength and impact strength. In addition, a particle size analysis (by Dynamic Light Scattering, DLS) was performed and the dispersion of the filler in the polymer matrix (Scanning Electron Microscopy, SEM), thermal parameters (Differential Scanning Calorimetry, DSC, and Dynamic Mechanical Analysis, DMA) were determined. Testing showed that biocomposites modified with diatomaceous earth have a higher mechanical strength than the reference system, especially with larger amounts of the filler (10 and 20%), e.g., the tensile strength of pure PA11 is about 46 MPa, while 20OB and 20OF 47.5 and 47 MPa, respectively, while an increase in max. flexural strength and flexural modulus is also observed compared to pure PA11 by a maximum of 63 and 54%, respectively Diatomaceous earth can be obtained in various ways-it is commercially available or it is possible to breed diatoms in laboratory conditions, while the use of commercially available diatomite, which contains diatoms of different sizes, eliminates the possibility of controlling mechanical parameters by filling biocomposites with a filler with the desired particle size distribution, and diatom breeding is not possible on an industrial scale. Our proposed biocomposite based on fractionated diatomaceous earth using a sedimentation process addresses the current need to produce biocomposite materials from natural sources, and moreover, the nature of the process, due to its simplicity, can be successfully used on an industrial scale.
PubMed: 35956665
DOI: 10.3390/polym14153153 -
Polymers Aug 2023Mechanical robustness and high energy efficiency of composite materials are immensely important in modern stretchable, self-powered electronic devices. However, the...
Fabrication of High-Performance Natural Rubber Composites with Enhanced Filler-Rubber Interactions by Stearic Acid-Modified Diatomaceous Earth and Carbon Nanotubes for Mechanical and Energy Harvesting Applications.
Mechanical robustness and high energy efficiency of composite materials are immensely important in modern stretchable, self-powered electronic devices. However, the availability of these materials and their toxicities are challenging factors. This paper presents the mechanical and energy-harvesting performances of low-cost natural rubber composites made of stearic acid-modified diatomaceous earth (mDE) and carbon nanotubes (CNTs). The obtained mechanical properties were significantly better than those of unfilled rubber. Compared to pristine diatomaceous earth, mDE has higher reinforcing efficiencies in terms of mechanical properties because of the effective chemical surface modification by stearic acid and enhanced filler-rubber interactions. The addition of a small amount of CNT as a component in the hybrid filler systems not only improves the mechanical properties but also improves the electrical properties of the rubber composites and has electromechanical sensitivity. For example, the fracture toughness of unfilled rubber (9.74 MJ/m) can be enhanced by approximately 484% in a composite (56.86 MJ/m) with 40 phr (per hundred grams of rubber) hybrid filler, whereas the composite showed electrical conductivity. At a similar mechanical load, the energy-harvesting efficiency of the composite containing 57 phr mDE and 3 phr CNT hybrid filler was nearly double that of the only 3 phr CNT-containing composite. The higher energy-harvesting efficiency of the mDE-filled conductive composites may be due to their increased dielectric behaviour. Because of their bio-based materials, rubber composites made by mDE can be considered eco-friendly composites for mechanical and energy harvesting applications and suitable electronic health monitoring devices.
PubMed: 37688238
DOI: 10.3390/polym15173612 -
Environmental Science and Pollution... Mar 2023The current study evaluates the efficacy of the entomopathogenic fungus Beauveria bassiana (Balsamo-Crivelli) Vuillemin (Hypocreales: Cordycipitaceae), diatomaceous...
The current study evaluates the efficacy of the entomopathogenic fungus Beauveria bassiana (Balsamo-Crivelli) Vuillemin (Hypocreales: Cordycipitaceae), diatomaceous earth (DE) (Protect-It), and the oxadiazine indoxacarb, at single or combined applications on wheat kernels, for the management of the rusty grain beetle, Cryptolestes ferrugineus (Stephens) (Coleoptera: Laemophloeidae), the red flour beetle, Tribolium castaneum (Herbst) (Coleoptera: Tenebrionidae), the khapra beetle, Trogoderma granarium Everts (Coleoptera: Dermestidae), and the lesser grain borer, Rhyzopertha dominica (F.) (Coleoptera: Bostrychidae). The study was conducted between November 2020 and August 2021 in Faisalabad under a complete randomized block design. The combination of DE + indoxacarb was the most efficient as it caused higher overall mortalities ranging between 59.34 and 100%, and lower overall progeny production ranging between 8.35 and 33.70 individuals per vial, than all other treatments. Beauveria bassiana alone exhibited the lowest mortality rates ranging between 22.33 and 47.76%, and the highest offspring emergence, ranging between 51.33 and 78.55 individuals per vial. Similar pattern was observed when persistence bioassays were conducted. For a period of 120 days, the DE + indoxacarb was the most powerful combination against all tested species, providing overall mortality rates between 17.06 and 63.80%. The overall progeny production was lower for the insect individuals exposed on wheat treated with the DE + indoxacarb combination, ranging between 13.66 and 52.23 individuals per vial, and higher for those exposed to B. bassiana alone, ranging between 44.03 and 107.67 individuals per vial, for the entire duration of storage. However, the efficacy of all treatments decreased gradually during the course of storage. The findings of the current study indicate that the combinations of entomopathogenic fungi, DE, and indoxacarb can be used for the prolonged protection of stored wheat from the tested noxious insect species of stored products. Further research, which will include other inert dusts in combination with entomopathogenic fungi and indoxacarb, may provide additional knowledge towards an effective management of noxious species occurring in storages.
Topics: Animals; Beauveria; Coleoptera; Diatomaceous Earth; Hypocreales; Insecta; Insecticides; Triticum
PubMed: 36640233
DOI: 10.1007/s11356-022-25075-1