-
Sensors (Basel, Switzerland) Jun 2024Salivary pH is one of the crucial biomarkers used for non-invasive diagnosis of intraoral diseases, as well as general health conditions. However, standard pH sensors...
Salivary pH is one of the crucial biomarkers used for non-invasive diagnosis of intraoral diseases, as well as general health conditions. However, standard pH sensors are usually too bulky, expensive, and impractical for routine use outside laboratory settings. Herein, a miniature hydrogel sensor, which enables quick and simple colorimetric detection of pH level, is shown. The sensor structure was manufactured from non-toxic hydrogel ink and patterned in the form of a matrix with 5 mm × 5 mm × 1 mm individual sensing pads using a 3D printing technique (bioplotting). The authors' ink composition, which contains sodium alginate, polyvinylpyrrolidone, and bromothymol blue indicator, enables repeatable and stable color response to different pH levels. The developed analysis software with an easy-to-use graphical user interface extracts the R(ed), G(reen), and B(lue) components of the color image of the hydrogel pads, and evaluates the pH value in a second. A calibration curve used for the analysis was obtained in a pH range of 3.5 to 9.0 using a laboratory pH meter as a reference. Validation of the sensor was performed on samples of artificial saliva for medical use and its mixtures with beverages of different pH values (lemon juice, coffee, black and green tea, bottled and tap water), and correct responses to acidic and alkaline solutions were observed. The matrix of square sensing pads used in this study provided multiple parallel responses for parametric tests, but the applied 3D printing method and ink composition enable easy adjustment of the shape of the sensing layer to other desired patterns and sizes. Additional mechanical tests of the hydrogel layers confirmed the relatively high quality and durability of the sensor structure. The solution presented here, comprising 3D printed hydrogel sensor pads, simple colorimetric detection, and graphical software for signal processing, opens the way to development of miniature and biocompatible diagnostic devices in the form of flexible, wearable, or intraoral sensors for prospective application in personalized medicine and point-of-care diagnosis.
Topics: Colorimetry; Printing, Three-Dimensional; Hydrogen-Ion Concentration; Saliva; Hydrogels; Humans; Biosensing Techniques
PubMed: 38931525
DOI: 10.3390/s24123740 -
Molecules (Basel, Switzerland) Jun 2024The preparation and application of the composite material "crosslinked polyvinyl alcohol-magnetite" as a sensitive matrix for use in digital colorimetry and optical...
The preparation and application of the composite material "crosslinked polyvinyl alcohol-magnetite" as a sensitive matrix for use in digital colorimetry and optical micrometry methods are discussed. The material was synthesized in the form of spherical granules (for micrometry) and thin films (for digital colorimetry). The obtained composites were characterized by the registration of magnetization curves. It was shown that the amount of grown FeO particles in the polymer gel is in linear dependence with the iron salt concentrations in the impregnating solutions. The composite granules were applied to determining monosaccharides using optical micrometry. The optimal pH value for the total amount of monosaccharides' determination was 8.6. The study of the analytical response of composite granules and films performed with a low limit of detection (7.9 mmol/dm) of both glucose and fructose and a possibility of the control of high alcohol contention in water media. The granules were used to determine the total carbohydrate content in samples of natural honey and syrups with high fructose contents, while the films were used to control the alcohol content in hand antiseptics. The results obtained are in good agreement with the data provided by the manufacturers.
PubMed: 38930858
DOI: 10.3390/molecules29122794 -
Micromachines May 2024Adapting to the growing demand for personalized, small-batch manufacturing, this study explores the development of additively manufactured molds for electroforming...
Adapting to the growing demand for personalized, small-batch manufacturing, this study explores the development of additively manufactured molds for electroforming personalized metal parts. The approach integrates novel multi-level mold design and fabrication techniques, along with the experimental procedures for the electroforming process. This work outlines design considerations and guidelines for effective electroforming in additively manufactured molds, successfully demonstrating the production of composite metal components with multi-level and free-form geometries. By emphasizing cost efficiency and part quality, particularly for limited-thickness metal components, the developed technique offers distinct advantages over existing metal additive manufacturing methods. This approach establishes itself as a flexible and durable method for metal additive manufacturing, expanding the scope of electroforming beyond traditional constraints such as thin-walled hollow structures, 2D components, and nanoscale applications.
PubMed: 38930706
DOI: 10.3390/mi15060734 -
Micromachines May 2024Additive manufacturing has advantages over other traditional manufacturing technologies for the fabrication of complex thin-walled parts. Previous correlation path...
Additive manufacturing has advantages over other traditional manufacturing technologies for the fabrication of complex thin-walled parts. Previous correlation path strategies, when applied to laser metal deposition processes, suffer from contour deposition transboundary and surface "scar" type overstacking. Therefore, this paper proposes a hybrid path generation method for the laser metal deposition process. First, the topological logic of the STL model of the part is restored to reduce redundant calculations at the stage of obtaining the layered contour. Then, the path points are planned on the basis of the offset contours in a helical upward trend to form a globally continuous composite path in space considering the melt channel width. Finally, vectors that adaptively fit to the model surface are generated for the path points as tool orientations and they are optimized by smoothing the rotation angles. The results of experiments conducted on a multi-axis machine equipped with a laser metal deposition module show that the path generated by the proposed method is not only capable of thin-walled structures with overhanging and curved surface features but also improves the surface imperfections of the part due to sudden changes in the angle of rotation while ensuring the boundary dimensions.
PubMed: 38930674
DOI: 10.3390/mi15060704 -
Materials (Basel, Switzerland) Jun 2024Three-dimensional printing technologies are becoming increasingly attractive for their versatility; the geometrical customizability and manageability of the final...
Three-dimensional printing technologies are becoming increasingly attractive for their versatility; the geometrical customizability and manageability of the final product properties are the key points. This work aims to assess the feasibility of producing radiopaque filaments for fused deposition modeling (FDM), a 3D printing technology, starting with zinc oxide (ZnO) and polylactic acid (PLA) as the raw materials. Indeed, ZnO and PLA are promising materials due to their non-toxic and biocompatible nature. Pellets of PLA and ZnO in the form of nanoparticles were mixed together using ethanol; this homogenous mixture was processed by a commercial extruder, optimizing the process parameters for obtaining mechanically stable samples. Scanning electron microscopy analyses were used to assess, in the extruded samples, the homogenous distribution of the ZnO in the PLA matrix. Moreover, X-ray microtomography revealed a certain homogenous radiopacity; this imaging technique also confirmed the correct distribution of the ZnO in the PLA matrix. Thus, our tests showed that mechanically stable radiopaque filaments, ready for FDM systems, were obtained by homogenously loading the PLA with a maximum ZnO content of 6.5% wt. (nominal). This study produced multiple outcomes. We demonstrated the feasibility of producing radiopaque filaments for additive manufacturing using safe materials. Moreover, each phase of the process is cost-effective and green-oriented; in fact, the homogenous mixture of PLA and ZnO requires only a small amount of ethanol, which evaporates in minutes without any temperature adjustment. Finally, both the extruding and the FDM technologies are the most accessible systems for the additive manufacturing commercial apparatuses.
PubMed: 38930261
DOI: 10.3390/ma17122892 -
Materials (Basel, Switzerland) Jun 2024Glass fiber-reinforced polymer (GFRP) laminates are used in many applications because of their availability, high mechanical properties, and cost-effectiveness. Fiber...
Glass fiber-reinforced polymer (GFRP) laminates are used in many applications because of their availability, high mechanical properties, and cost-effectiveness. Fiber defects in the form of waviness or wrinkles can occur during the production of multilayered laminates. When curved laminates of significant thickness are produced, the likelihood of such defects increases. Studies have confirmed that fiber deformation during manufacture leads to a reduction in the mechanical properties of laminates. Therefore, early detection of such defects is essential. The main part of this paper deals with research into the possibility of using active infrared thermography to detect wrinkles in curved multilayered GFRP laminates. The size of the artificial wrinkles was assessed by analyzing scans and microimages. The shape deformations of the samples were evaluated by comparing the samples with the mold and the assumed nominal shape. The influence of the out-of-autoclave manufacturing process on the reduction in wrinkles formed without significantly affecting the internal structure of the laminate is presented in this work. This research demonstrated the ability to detect wrinkles in thick curved laminates using active infrared thermography. However, it also showed how the interpretation of the thermographic results is affected by the curvature of the structure, the lack of uniform heating, and the configuration of the thermographic setup.
PubMed: 38930199
DOI: 10.3390/ma17122830 -
Advanced Science (Weinheim,... Jun 2024Dislocation of anti-adhesion materials, non-specific tissue adhesion, and the induction of secondary fibrinolysis disorders are the main challenges faced by...
Dislocation of anti-adhesion materials, non-specific tissue adhesion, and the induction of secondary fibrinolysis disorders are the main challenges faced by postoperative anti-adhesion materials. Herein, a self-leveling transient unilateral adhesive hydrogel is custom-designed to conquer these challenges with a theoretically calculated and dual-step tailored gellan gum (GG) as the sole agent. First, the maximum gelation temperature of GG is lowered from 42-25 °C through controlled perturbation of intra- and inter-molecular hydrogen bonds, which is achieved by employing the methacrylic anhydride as a "hydrogen bond's perturbator" to form methacrylate GG (MeGG). Second, the "self-leveling" injectability and wound shape adaptably are endowed by the formation of borate-diol complexed MeGG (BMeGG). Finally, the transient unilateral tissue-adhesive hydrogel (BMeGG-H) barrier is prepared through photo-controlled cross-linking of reactive alkenyl groups. This degradable hydrogel demonstrates favorable rheological properties, light-controlled unilateral adhesion properties, biocompatibility, anti-fibrin adhesion, and anti-cell adhesion properties in vitro. Comprehensive regulation of the fibrinolysis balance toward non-adhesion is conformed in a rat model after intra-abdominal surgery via anti-autoinflammatory response, intestinal wall integrity repair, and Tissue plasminogen activator (t-PA) and plasminogen activator inhibitor-1 (PAI-1) balance adjustment. Notably, the 14 day anti-adhesion effective rate is 100%, indicating its significant potential in clinical applications for postoperative anti-adhesion.
PubMed: 38924679
DOI: 10.1002/advs.202403626 -
ACS Applied Materials & Interfaces Jun 2024Lithium-ion batteries are the leading energy storage technology for portable electronics and vehicle electrification. However, demands for enhanced energy density,...
Lithium-ion batteries are the leading energy storage technology for portable electronics and vehicle electrification. However, demands for enhanced energy density, safety, and scalability necessitate solid-state alternatives to traditional liquid electrolytes. Moreover, the rapidly increasing utilization of lithium-ion batteries further requires that next-generation electrolytes are derived from earth-abundant raw materials in order to minimize supply chain and environmental concerns. Toward these ends, clay-based nanocomposite electrolytes hold significant promise since they utilize earth-abundant materials that possess superlative mechanical, thermal, and electrochemical stability, which suggests their compatibility with energy-dense lithium metal anodes. Despite these advantages, nanocomposite electrolytes rarely employ kaolinite, the most abundant variety of clay, due to strong interlayer interactions that have historically precluded efficient exfoliation of kaolinite. Overcoming this limitation, here we demonstrate a scalable liquid-phase exfoliation process that produces kaolinite nanoplatelets (KNPs) with high gravimetric surface area, thus enabling the formation of mechanically robust nanocomposites. In particular, KNPs are combined with a succinonitrile (SN) liquid electrolyte to form a nanocomposite gel electrolyte with high room-temperature ionic conductivity (1 mS cm), stiff storage modulus (>10 MPa), wide electrochemical stability window (4.5 V vs Li/Li), and excellent thermal stability (>100 °C). The resulting KNP-SN nanocomposite gel electrolyte is shown to be suitable for high-rate rechargeable lithium metal batteries that employ high-voltage LiNiCoAlO (NCA) cathodes. While the primary focus here is on solid-state batteries, our strategy for kaolinite liquid-phase exfoliation can serve as a scalable manufacturing platform for a wide variety of other kaolinite-based nanocomposite applications.
PubMed: 38924489
DOI: 10.1021/acsami.4c03997 -
Acta Ophthalmologica Jun 2024To develop and evaluate a photovoltaic, wireless wide-field epiretinal prosthesis for the treatment of retinitis pigmentosa.
PURPOSE
To develop and evaluate a photovoltaic, wireless wide-field epiretinal prosthesis for the treatment of retinitis pigmentosa.
METHODS
A mosaic array of thinned silicon-based photodiodes with integrated thin-film stimulation electrodes was fabricated with a flexible polyimide substrate film to form a film-based miniaturized electronic system with wireless optical power and signal transmission and integrated electrostimulation. Manufactured implants were characterized with respect to their optoelectronic performance and biocompatibility following DIN EN ISO 10993.
RESULTS
A 14 mm diameter prosthesis containing 1276 pixels with a maximum sensitivity at a near infrared wavelength of 905 nm and maximized stimulation current density 30-50 μm below the electrodes was developed for direct activation of retinal ganglion cells during epiretinal stimulation. Fabricated prostheses demonstrated mucosal tolerance and the preservation of both metabolic activity, proliferation and membrane integrity of human fibroblasts as well as the retinal functions of bovine retinas. Illumination of the prosthesis, which was placed epiretinally on an isolated perfused bovine retina, with infrared light resulted in electrophysiological recordings reminiscent of an a-wave (hyperpolarization) and b-wave (depolarization).
CONCLUSIONS
A photovoltaic, wireless wide-field epiretinal prosthesis for the treatment of retinitis pigmentosa using near infrared light for signal transmission was designed, manufactured and its biocompatibility and functionality demonstrated in vitro and ex vivo.
PubMed: 38923194
DOI: 10.1111/aos.16733 -
Journal of Fungi (Basel, Switzerland) Jun 2024Eucalyptus roots form symbiotic relationships with arbuscular mycorrhizal (AM) fungi in soil to enhance adaptation in challenging environments. However, the evolution of...
Eucalyptus roots form symbiotic relationships with arbuscular mycorrhizal (AM) fungi in soil to enhance adaptation in challenging environments. However, the evolution of the AM fungal community along a chronosequence of eucalypt plantations and its relationship with soil properties remain unclear. In this study, we evaluated the tree growth, soil properties, and root AM fungal colonization of W. Hill ex Maiden plantations at different ages, identified the AM fungal community composition by high-throughput sequencing, and developed a structural equation model among trees, soil, and AM fungi. Key findings include the following: (1) The total phosphorus (P) and total potassium (K) in the soil underwent an initial reduction followed by a rise with different stand ages. (2) The rate of AM colonization decreased first and then increased. (3) The composition of the AM fungal community changed significantly with different stand ages, but there was no significant change in diversity. (4) and were the dominant genera, accounting for 70.1% and 21.8% of the relative abundance, respectively. (5) The dominant genera were mainly influenced by soil P, the N content, and bulk density, but the main factors were different with stand ages. The results can provide a reference for fertilizer management and microbial formulation manufacture for eucalyptus plantations.
PubMed: 38921389
DOI: 10.3390/jof10060404