-
Materials (Basel, Switzerland) Jun 2024Alite(CS)-Ye'elimite(CA$) cement is a high cementitious material that incorporates a precise proportion of ye'elimite into the ordinary Portland cement. The synthesis...
Alite(CS)-Ye'elimite(CA$) cement is a high cementitious material that incorporates a precise proportion of ye'elimite into the ordinary Portland cement. The synthesis and hydration behavior of Alite-Ye'elimite clinker with different lime saturation factors were investigated. The clinkers were synthesized using a secondary thermal treatment process, and their compositions were characterized. The hydrated pastes were analyzed for their hydration products, pore structure, mechanical strength, and microstructure. The clinkers and hydration products were characterized using XRD, TG-DSC, SEM, and MIP analysis. The results showed that the Alite-Ye'elimite cement clinker with a lime saturation factor (KH) of 0.93, prepared through secondary heat treatment, contained 64.88% CS and 2.06% CA$. At this composition, the Alite-Ye'elimite cement clinker demonstrated the highest 28-day strength. The addition of SO to the clinkers decreased the content of tricalcium aluminate (CA) and the ratio of Alite/Belite (CS/CS), resulting in a preference for belite formation. The pore structure of the hydrated pastes was also investigated, revealing a distribution of pore sizes ranging from 0.01 to 10 μm, with two peaks on each differential distribution curve corresponding to micron and sub-micron pores. The pore volume decreased from 0.22 ± 0.03 to 0.15 ± 0.18 cm g, and the main peak of pore distribution shifted towards smaller sizes with increasing hydration time.
PubMed: 38930403
DOI: 10.3390/ma17123035 -
Materials (Basel, Switzerland) Jun 2024Lotus-type porous metals, characterized by low densities, large surface areas, and directional properties, are contemporarily utilized as lightweight, catalytic, and...
Lotus-type porous metals, characterized by low densities, large surface areas, and directional properties, are contemporarily utilized as lightweight, catalytic, and energy-damping materials; heat sinks; etc. In this study, the effects of dimensionless working parameters on the morphology of lotus-type pores in metals during unidirectional solidification were extensively investigated via general algebraic expressions. The independent dimensionless parameters include metallurgical, transport, and geometrical parameters such as Sieverts' law constant, a partition coefficient, the solidification rate, a mass transfer coefficient, the imposed mole fraction of a solute gas, the total pressure at the top free surface, hydrostatic pressure, a solute transport parameter, inter-pore spacing, and initial contact angle. This model accounts for transient gas pressure in the pore, affected by the solute transfer, gas, capillary, and hydrostatic pressures, and Sieverts' laws at the bubble cap and top free surface. Solute transport across the cap accounts for solute convection at the cap and the amount of solute rejected by the solidification front into the pore. The shape of lotus-type pores can be described using a proposed fifth-degree polynomial approximation, which captures the major portions between the initial contact angle and the maximum radius at a contact angle of 90 degrees, obtained by conserving the total solute content in the system. The proposed polynomial approximation, along with its working parameters, offers profound insights into the formation and shape of lotus-type pores in metals. It systematically provides deep insights into mechanisms that may not be easily revealed with experimental studies. The prediction of a lotus-type pore shape is thus algebraically achieved in good agreement with the available experimental data and previous analytical results.
PubMed: 38930382
DOI: 10.3390/ma17123013 -
Materials (Basel, Switzerland) Jun 2024Porous copper (Cu), with varying porosities, has been made using carbamide as a space holder through the powder metallurgy route. Two shapes of carbamide particles were...
Porous copper (Cu), with varying porosities, has been made using carbamide as a space holder through the powder metallurgy route. Two shapes of carbamide particles were used, (i) needlelike and (ii) spherical, in order to investigate the effect of the space holder shape on the pore structure and mechanical properties of porous Cu. The compressive deformation behavior of porous Cu was studied under a compression test. The pores' structural characteristics and mechanical properties of the porous Cu varied significantly with the shape of the space holder. Although the effect of the space holder shape on the porosity was not regular, the effect on the mechanical properties was regular. The stress increased monotonically with the increase in the strain, and strain hardening occurred at the plastic yield stage. The elastic modulus and yield strength followed the power law, with the relative density irrespective of the space holder shape. The empirical constants associated with different empirically developed power law relations were different, according to the shape of space holder. A quantitative relationship between the elastic modulus and yield strength and the spacer content was obtained to control the mechanical properties of the present porous Cu or other porous metals and metal foams using the well-known space holder method.
PubMed: 38930377
DOI: 10.3390/ma17123008 -
Materials (Basel, Switzerland) Jun 2024The effect of an alternative source of silica, based on class F fly ash mixed with blast furnace slag and activated by rice husk ash (RHA), to produce concrete exposed...
The effect of an alternative source of silica, based on class F fly ash mixed with blast furnace slag and activated by rice husk ash (RHA), to produce concrete exposed to marine environments was evaluated. Four mixtures activated by the combination of 85% NaOH 14M + 15% RHA were manufactured to achieve a liquid/solid ratio of 0.20. Fly ash was incorporated into the steel slag mixture at addition percentages of 20, 40, 60, and 80%, and evaluated at 28, 900, and 1800 days for pore and chloride ion absorption. In general, including rice husk ash in the mixture of fly ash and steel slag significantly affected mechanical performance because it was possible to obtain concrete with high mechanical resistance. Concerning the durability evaluation, the effect of the activator generated by rice husk ash was observed, and the increase in steel slag added to the cementitious samples improved the capacity of the material to resist the penetration and diffusion of chloride ions.
PubMed: 38930370
DOI: 10.3390/ma17123001 -
Materials (Basel, Switzerland) Jun 2024This paper investigates the high temperature resistance performance and mechanism of potassium-activated blended precursor geopolymer with silica fume. The failure...
This paper investigates the high temperature resistance performance and mechanism of potassium-activated blended precursor geopolymer with silica fume. The failure morphology, volume, and mass loss, compressive strength deterioration, hydration production, and pore structure are measured and analyzed. The results show that introducing slag into fly ash-based geopolymer could greatly improve the 28 d compressive strength but reduce the thermal stability. In contrast, the partial substitution of fly ash by metakaolin contributes to excellent high temperature resistance with slightly enhanced 28 d compressive strength. After being exposed at 800 °C, the residual compressive strength of F7M3 remains at 37 MPa, almost 114% of the initial ambient-temperature strength. An appropriately enlarged silica fume content in geopolymer results in increased compressive strength and enhanced thermal stability. However, an excessive silica fume content is detrimental to the generation of alkali-aluminosilicate gels and ceramic-like phases and thus exacerbates the high temperature damage.
PubMed: 38930345
DOI: 10.3390/ma17122975 -
Materials (Basel, Switzerland) Jun 2024A novel UV-light-curable poly(ethylene glycol) diacrylate matrix composite material with unmodified and methacryloxyl-grafted TiO and TiO-ZrO systems was developed and...
A novel UV-light-curable poly(ethylene glycol) diacrylate matrix composite material with unmodified and methacryloxyl-grafted TiO and TiO-ZrO systems was developed and tested as a potential coating material for medical components. The main goal of the research was to evaluate how the addition of (un)modified inorganic oxide fillers affects the properties of the composition (viscosity, UV/Vis spectra), the kinetics of photocuring (photo-DSC), and the morphological (SEM), physicochemical, and thermal properties (DSC, TGA) of the resulting composites. The applied filler functionalization process decreased their polarity and changed their size, BET surface area, and pore volume, which influenced the viscosity and kinetics of the photocurable system. In addition, the addition of synthesized fillers reduced the polymer's glass transition temperature and increased its thermal stability. It was also observed that additional UV irradiation of the tested composite changed its surface, resulting in hydrophobic properties (with the addition of 7 wt.% filler, an increase in the contact angle by more than 45% was observed).
PubMed: 38930277
DOI: 10.3390/ma17122908 -
Materials (Basel, Switzerland) Jun 2024In this work, the preparation of titanium sponge by magnesium thermal method is regarded as the liquid-phase sintering process of titanium, and powder-metallurgy...
In this work, the preparation of titanium sponge by magnesium thermal method is regarded as the liquid-phase sintering process of titanium, and powder-metallurgy sintering technology is utilized to simulate the aggregation-growth and densification behavior of titanium particles in a high-temperature liquid medium (the molten Mg-MgCl system). It was found that compared with MgCl, Mg has better high-temperature wettability and reduction effect, which promotes titanium particles to form a sponge titanium skeleton at lower temperature. The aggregation degree of titanium particles and the densification degree of a sponge titanium skeleton can be improved by increasing the temperature and the relative content of Mg in the melting medium. The kinetics study shows that with the increase in temperature, the porosity of the titanium particle aggregates and the sponge titanium skeleton decreases, and their density growth rate increases. With the extension of time, the aggregation degree of titanium particles and the densification degree of sponge titanium gradually increase. This work provides a theoretical reference for controlling the density of titanium sponge in industry.
PubMed: 38930273
DOI: 10.3390/ma17122904 -
Materials (Basel, Switzerland) Jun 2024The paper presents the study concerning the preparation and physio-chemical and biological properties of wool-copper (WO-Cu) materials obtained by the sputter deposition...
The paper presents the study concerning the preparation and physio-chemical and biological properties of wool-copper (WO-Cu) materials obtained by the sputter deposition of copper onto the wool fibers. The WO-Cu material was subjected to physio-chemical and biological investigations. The physio-chemical investigations included the elemental analysis of materials (C, N, O, S, and Cu), their microscopic analysis, and surface properties analysis (specific surface area and total pore volume). The biological investigations consisted of the antimicrobial activity tests of the WO-Cu materials against colonies of Gram-positive () bacteria, Gram-negative () bacteria, and fungal mold species (). Biochemical-hematological tests included the evaluation of the activated partial thromboplastin time and pro-thrombin time. The tested wool-copper demonstrated the ability to interact with the DNA in a time-dependent manner. These interactions led to the DNA's breaking and degradation. The antimicrobial and antifungal activities of the WO-Cu materials suggest a potential application as an antibacterial/antifungal material. Wool-copper materials may be also used as customized materials where the blood coagulation process could be well controlled through the appropriate copper content.
PubMed: 38930247
DOI: 10.3390/ma17122878 -
Materials (Basel, Switzerland) Jun 2024Rigid porous polymeric monoliths are robust, highly efficient, versatile stationary phases. They offer simple preparation and convenient modification provided by a whole...
Rigid porous polymeric monoliths are robust, highly efficient, versatile stationary phases. They offer simple preparation and convenient modification provided by a whole range of synthesis factors, e.g., starting monomers, cross-linkers, initiators, porogens, polymerization techniques, and temperature. The main aim of this study was to synthesize polymeric monoliths and determine the correlation between polymerization parameters and the porosity and thermal stability of the obtained materials. Polymeric monoliths were synthesized directly in HPLC columns using -vinyl-2-pyrrolidone (NVP) and 4-vinylpiridine (4VP) as functional monomers, with trimethylolpropane trimethacrylate (TRIM) serving as the cross-linking monomer. During copolymerization a mixture of cyclohexanol/decane-1-ol was used as the pore-forming diluent. Polymerization was carried out at two different temperatures: 55 and 75 °C. As a result, monoliths with highly developed internal structure were synthesized. The value of their specific surface area was in the range of 92 m/g to 598 m/g, depending on the monomer composition and polymerization temperature. Thermal properties of the obtained materials were investigated by means of thermogravimetry (TG). Significant differences in thermal behavior were noticed between monoliths synthesized at 55 and 75 °C. Additionally, the poly(NVP--TRIM) monolith was successfully applied in GC analyses.
PubMed: 38930229
DOI: 10.3390/ma17122860 -
Materials (Basel, Switzerland) Jun 2024Changing the morphology is an excellent option for altering the textural parameters of SBA-15 materials. This study provides a guide on how the properties of mesoporous...
Changing the morphology is an excellent option for altering the textural parameters of SBA-15 materials. This study provides a guide on how the properties of mesoporous structures behave according to their morphology and their contribution to thermal stability. The objective of this work was to synthesize different morphologies (spherical, hexagonal prisms, rice-like grains, rods, and fibers) of SBA-15 materials and evaluate the existing textural changes. The materials were synthesized by varying the temperature of the synthesis gel from 25 °C to 55 °C, with stirring at 300 or 500 rpm. The results of X-ray diffraction, Fourier transform infrared spectroscopy, N adsorption and desorption, and scanning electron microscopy were evaluated. Thermal stability tests were also conducted in an inert atmosphere. The materials were successfully synthesized, and it was observed that they all exhibited different characteristics, such as their ordering, interplanar distance, mesoporous parameter, specific surface area, micropore and mesopore volumes, external mesoporous area, and wall thickness. They also presented different thermal stabilities. The rice grain morphology had the highest specific surface area (908.8 cm/g) and the best thermal stability, while the rod morphology had the best pore diameter (7.7 nm) and microporous volume (0.078 cm/g).
PubMed: 38930197
DOI: 10.3390/ma17122827