-
Microbiology Spectrum Jun 2024Biosorption and biomineralization are commonly used for the immobilization of metal ions. Biosorption is commonly used as a green method to enrich rare earth ions from...
UNLABELLED
Biosorption and biomineralization are commonly used for the immobilization of metal ions. Biosorption is commonly used as a green method to enrich rare earth ions from wastewater. However, little attention has been paid to the facilitating role of biomineralization in the enrichment of rare earth ions. In this study, a strain of sp. DW015, isolated from ion adsorption type rare earth ores and a urease-producing strain were used to enrich rare earth elements (REEs) from an aqueous solution. The results indicate that biomineralization accelerates the enrichment of Terbium(III) compared to biosorption alone. Kinetic analysis suggests that the main mode of action of DW015 was biosorption, following pseudo-second-order kinetics ( = 0.998). The biomineralization of DW015 did not significantly contribute to the enrichment of Tb(III), whereas excessive biomineralization of led to a decrease in the enrichment of Tb(III). A synergistic system of biosorption and biomineralization was established by combining the two bacteria, with the optimal mixed bacteria (:DW015) ratio being 1:19. This study provides fundamental support for the synergistic effect of biosorption and biomineralization and offers a new reference for future microbial-based enrichment methods.
IMPORTANCE
A weak microbially induced calcium carbonate precipitation (MICP) promotes the enrichment of Tb(III) by bacteria, while a strong MICP leads to the release of Tb(III). However, existing explanations cannot elucidate these mechanisms. In this study, the morphology of the bioprecipitation and the degree of Tb(III) enrichment were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS). The data revealed that MICP could drive stable attachment of Tb(III) onto the cell surface, forming a Tb-CaCO mixed solid phase. Excessive rapid rate of calcite generation could disrupt the Tb(III) adsorption equilibrium, leading to the release of Tb(III). Therefore, in order for Tb(III) to be stably embedded in calcite, it is necessary to have a sufficient number of adsorption sites on the bacteria and to regulate the rate of MICP. This study provides theoretical support for the process design of MICP for the enrichment of rare earth ions.
PubMed: 38916328
DOI: 10.1128/spectrum.00760-24 -
Journal of Nanobiotechnology Jun 2024Photothermal therapy (PTT) is a promising cancer treatment method due to its ability to induce tumor-specific T cell responses and enhance therapeutic outcomes. However,...
Photothermal therapy (PTT) is a promising cancer treatment method due to its ability to induce tumor-specific T cell responses and enhance therapeutic outcomes. However, incomplete PTT can leave residual tumors that often lead to new metastases and decreased patient survival in clinical scenarios. This is primarily due to the release of ATP, a damage-associated molecular pattern that quickly transforms into the immunosuppressive metabolite adenosine by CD39, prevalent in the tumor microenvironment, thus promoting tumor immune evasion. This study presents a photothermal nanomedicine fabricated by electrostatic adsorption among the Fe-doped polydiaminopyridine (Fe-PDAP), indocyanine green (ICG), and CD39 inhibitor sodium polyoxotungstate (POM-1). The constructed Fe-PDAP@ICG@POM-1 (FIP) can induce tumor PTT and immunogenic cell death when exposed to a near-infrared laser. Significantly, it can inhibit the ATP-adenosine pathway by dual-directional immunometabolic regulation, resulting in increased ATP levels and decreased adenosine synthesis, which ultimately reverses the immunosuppressive microenvironment and increases the susceptibility of immune checkpoint blockade (aPD-1) therapy. With the aid of aPD-1, the dual-directional immunometabolic regulation strategy mediated by FIP can effectively suppress/eradicate primary and distant tumors and evoke long-term solid immunological memory. This study presents an immunometabolic control strategy to offer a salvage option for treating residual tumors following incomplete PTT.
Topics: Animals; Photothermal Therapy; Immunotherapy; Mice; Nanomedicine; Tumor Microenvironment; Cell Line, Tumor; Humans; Indocyanine Green; Neoplasms; Adenosine Triphosphate; Adenosine; Mice, Inbred C57BL; Apyrase; Female; Phototherapy
PubMed: 38915007
DOI: 10.1186/s12951-024-02643-w -
Scientific Reports Jun 2024Enrichment of ultrafine liberated valuable minerals from their associated gangue phases is one of the emerging investigation topics within mineral processing and...
Enrichment of ultrafine liberated valuable minerals from their associated gangue phases is one of the emerging investigation topics within mineral processing and recycling. Using green flotation reagents and turning processes into eco-friendly systems is also one of the challenges in the green transition of ore beneficiation plants. Starch and Tanin as biodegradable depressants for hematite depression have been commercially used in various iron ore processing plants. However, their depression effects on ultrafine particles were not systemically assessed and compared. To fill this gap, this investigation examined the effects of starch, tannin, their mixtures (different ratios), and their different conditioning sequence on the floatability of ultrafine quartz and hematite (- 15 µm). Since the macromolecular polymer of these biodegradable depressants can bind particles together and flocculate them, turbidity analyses were used to assess their optimum ratio for hematite depression without affecting quartz floatability. Turbidity analyses provided a mixture of tannin and starch might enhance the flotation separation of quartz from hematite. Starch could flocculate ultrafine hematite particles, while tannin could disperse ultrafine quartz particles. Floatability experiments indicated that starch had the highest performance in hematite depression (lowest effect on quartz particles) compared to other conditions. Surface analyses (zeta potential and FTIR) proved floatability outcomes and highlighted starch had stronger adsorption on the hematite surface than tannin.
PubMed: 38914738
DOI: 10.1038/s41598-024-65515-1 -
Scientific Reports Jun 2024Investigating surfactant effects on the floatability of Wiser bituminous coal holds significant importance in improving coal cleanliness and utilization value. Using...
Investigating surfactant effects on the floatability of Wiser bituminous coal holds significant importance in improving coal cleanliness and utilization value. Using density functional theory and molecular dynamics simulation methods, this study constructed models of Wiser bituminous coal and examined the impact of different surfactants, including the anionic surfactant sodium dodecyl benzene sulfonate, the cationic surfactant hexadecyl trimethyl ammonium bromide (CTAB), and the non-ionic surfactant fatty alcohol ethoxylated ether. The focus was on investigating the charge distribution characteristics of these molecules and the modifying effect of binary surfactants on the hydrophobicity of bituminous coal. Results revealed that the maximum electrostatic potential was concentrated near oxygen/nitrogen/sulfur-containing functional groups like sulfonic acid groups, quaternary ammonium cations, ethylene oxide, hydroxyl groups, carboxyl groups, and sulfur bonds. These functional groups exhibited a propensity for accepting/delivering electrons to form hydrogen bonds. Among the surfactants tested, CTAB revealed the slightest difference in frontier orbital energy, measuring 3.187 eV, thereby demonstrating a superior trapping ability compared with the other two surfactants. Adsorption reactions within the system were determined to be spontaneous, with over 60% of the interaction force attributed to electrostatic forces. Moreover, the repulsive force magnitude with water molecules followed the trend: sulfonate group (2.20 Å) < ethylene oxide (2.43 Å) < quaternary ammonium cation (2.57 Å), indicating more excellent water repellency of CTAB. Findings showed that CTAE binary surfactants proved most effective in modifying the hydrophobicity of bituminous coal. This study offers valuable insights into reducing waste, pollution, and resource wastage.
PubMed: 38914729
DOI: 10.1038/s41598-024-65466-7 -
Scientific Reports Jun 2024World production of dyes is estimated at more than 800,000 t·yr. The purpose of this research falls within the scope of the choice of an effective, local, and...
World production of dyes is estimated at more than 800,000 t·yr. The purpose of this research falls within the scope of the choice of an effective, local, and inexpensive adsorbent to remove dyes from wastewater. Adsorptive elimination of dyes by commonly accessible adsorbents is inefficient. The metal-organic frameworks (MOFs) are an important class of porous materials offering exceptional properties as adsorbents by improving separation efficiency compared to existing commercial adsorbents. However, its powder form limits its applications. One way to overcome this problem is to trap them in a flexible matrix to form a hierarchical porous composite. Therefore, in this work, we prepared MIL-100 (Fe) embedded in a cellulose matrix named MIL-100(Fe)/Cell, and used it as an adsorbent of methylene blue (MB) dye. According to the BET analysis, the specific surface area of the synthesized MOF is 294 m/g which is related to the presence of the cellulose as efficient and green support. The structure of this composite is approximately hexagonal. Adsorption was studied as a function of contact time, adsorbent mass and pollutant load (concentration), and pH, and the effect of each of them on absorption efficiency was optimized. The MIL-100(Fe)/Cell was capable of removing 98.94% of MB dye with an initial concentration of 150 mg/L within 10 min at pH = 6.5 and room temperature. The obtained maximum adsorption capacity was 384.615 mg/g. The adsorption isotherm is consistent with the Langmuir models. The mechanism of MB adsorption proceeds through п-п and electrostatic interactions.
PubMed: 38914657
DOI: 10.1038/s41598-024-65531-1 -
Scientific Reports Jun 2024Sugarcane bagasse fly ash, a residual product resulting from the incineration of biomass to generate power and steam, is rich in SiO. Sodium silicate is a fundamental...
Sugarcane bagasse fly ash, a residual product resulting from the incineration of biomass to generate power and steam, is rich in SiO. Sodium silicate is a fundamental material for synthesizing highly porous silica-based adsorbents to serve circular practices. Aflatoxin B1 (AFB1), a significant contaminant in animal feeds, necessitates the integration of adsorbents, crucial for reducing aflatoxin concentrations during the digestive process of animals. This research aimed to synthesize aluminosilicate and zinc silicate derived from sodium silicate based on sugarcane bagasse fly ash, each characterized by a varied molar ratio of aluminum (Al) to silicon (Si) and zinc (Zn) to silicon (Si), respectively. The primary focus of this study was to evaluate their respective capacities for adsorbing AFB1. It was revealed that aluminosilicate exhibited notably superior AFB1 adsorption capabilities compared to zinc silicate and silica. Furthermore, the adsorption efficacy increased with higher molar ratios of Al:Si for aluminosilicate and Zn:Si for zinc silicate. The N confirmed AFB1 adsorption within the pores of the adsorbent. In particular, the aluminosilicate variant with a molar ratio of 0.08 (Al:Si) showcased the most substantial AFB1 adsorption capacity, registering at 88.25% after an in vitro intestinal phase. The adsorption ability is directly correlated with the presence of surface acidic sites and negatively charged surfaces. Notably, the kinetics of the adsorption process were best elucidated through the application of the pseudo-second-order model, effectively describing the behavior of both aluminosilicate and zinc silicate in adsorbing AFB1.
Topics: Silicates; Adsorption; Aluminum Silicates; Saccharum; Aflatoxin B1; Coal Ash; Cellulose; Zinc Compounds
PubMed: 38914625
DOI: 10.1038/s41598-024-65158-2 -
Scientific Reports Jun 2024Worldwide industrialization has grown at a rapid pace, contaminating water resources, particularly with phenolic pollutants that pose a risk to aquatic systems and human...
Worldwide industrialization has grown at a rapid pace, contaminating water resources, particularly with phenolic pollutants that pose a risk to aquatic systems and human health. The goal of this study is to create an inexpensive magnetic composite that can effectively remove nitrophenol (o-NP) using adsorptive means. In this instance, a nonanyl chitosan (N-Cs) derivative was synthesized and then combined with activated petroleum coke (AP-coke) and magnetic FeO to boost its adsorbability towards o-NP and to facilitate its separation. Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X-ray diffractometer (XRD), Vibrating sample magnetometer (VSM), X-ray photoelectron spectroscopy (XPS), and zeta potential were employed to characterize the magnetic composite. The experimental results indicated that the FeO/AP-coke/N-Cs composite possesses a greater affinity toward o-NP with a maximal efficiency reached 88% compared to 22.8, 31.2, and 45.8% for FeO, AP-coke and N-Cs, respectively. The equilibrium adsorption data coincided with the Langmuir, Freundlich, and Temkin isotherm models, with a maximum adsorption capacity of 291.55 mg/g at pH 6, whereas the pseudo second order kinetic model offered the best fit to the experimental data. Besides, the developed adsorbent preserved satisfactory adsorption characteristics after reuse for five successive cycles. The proposed adsorption mechanism involves the H-bonding, π-π interaction, hydrophobic interactions and electron donor-acceptor interactions. These findings hypothesize that the constructed magnetic composite could efficiently remove nitrophenols from polluted water with high performance and ease-separation.
PubMed: 38914588
DOI: 10.1038/s41598-024-64117-1 -
Nature Communications Jun 2024Transition metal chalcogenides have been identified as low-cost and efficient electrocatalysts to promote the hydrogen evolution reaction in alkaline media. However, the...
Transition metal chalcogenides have been identified as low-cost and efficient electrocatalysts to promote the hydrogen evolution reaction in alkaline media. However, the identification of active sites and the underlying catalytic mechanism remain elusive. In this work, we employ operando X-ray absorption spectroscopy and near-ambient pressure X-ray photoelectron spectroscopy to elucidate that NiS undergoes an in-situ phase transition to an intimately mixed phase of NiS and NiO, generating highly active synergistic dual sites at the NiS/NiO interface. The interfacial Ni is the active site for water dissociation and OH* adsorption while the interfacial S acts as the active site for H* adsorption and H evolution. Accordingly, the in-situ formation of NiS/NiO interfaces enables NiS electrocatalysts to achieve an overpotential of only 95 ± 8 mV at a current density of 10 mA cm. Our work highlighted that the chemistry of transition metal chalcogenides is highly dynamic, and a careful control of the working conditions may lead to the in-situ formation of catalytic species that boost their catalytic performance.
PubMed: 38914549
DOI: 10.1038/s41467-024-49015-4 -
PloS One 2024The adsorption and desorption of phosphorus (P) in soil constitute a crucial internal cycle that is closely associated with soil fertility, exerting direct influence on...
The adsorption and desorption of phosphorus (P) in soil constitute a crucial internal cycle that is closely associated with soil fertility, exerting direct influence on the quantity, form, and availability of P within the soil. The vertical spatial variation characteristics of soil adsorption and desorption were investigated for the 0-100 cm soil layer in the northeast black soil region in this study. The maximum adsorption capacity (Qmax) and maximum adsorption buffer capacity (MBC) of black soil in the study area ranged from 313.8 to 411.9 mg kg-1 and from 3.1 to 28.8 L kg-1, respectively, within the soil layer of 0-100 cm depth, exhibiting an increasing trend with greater soil depth. The degree of P adsorption saturation (DPS) exhibited a contrasting trend with the variations in Qmax and MBC, ranging from 3.8% to 21.6%. The maximum desorption capacity (Dmax) and desorption rate (Dr) of soil P ranged from 112.8 to 215.7 mg kg-1 and 32.1% to 52.5%, respectively, while the readily desorbable P (RDP) in soil was within the range of 1.02 to 3.35 mg kg-1. Both Dmax, Dr, and RDP exhibited a decreasing trend with increasing soil depth before showing an upward trend. These research findings not only provide essential background data for the systematic investigation of soil P in the black soil region but also serve as a valuable reference for assessing soil quality in this area.
Topics: Phosphorus; Soil; Adsorption; China
PubMed: 38913687
DOI: 10.1371/journal.pone.0306145 -
Heliyon Jun 2024Functional bioactive ingredients isolated from microalgae as sustainable sources have become a new subject of pharmacology and functional foods. Thus, the work aims to...
Characterization of C-phycocyanin antioxidant, anti-inflammatory, anti-tumour, and anti-HCoV-229E activities and encapsulation for implementation in an innovative functional yogurt.
Functional bioactive ingredients isolated from microalgae as sustainable sources have become a new subject of pharmacology and functional foods. Thus, the work aims to produce crude phycocyanin (C-PC), define it, and investigate its pharmacological effects before warping it in a nanophytosome. Subsequently, the physicochemical properties of nanoparticles were evaluated. Both free and nanophytosomes of C-PC were incorporated into cow milk fermented with the probiotic KU985435 to make functional yoghurt and the stability of C-PC of both phytosomes was assessed. The amino acid content of C-PC revealed the presence of eight of nine essential amino acids and eight of eleven non-essential amino acids. C-PC has a medium molecular weight (82.992 kDa). Some pharmacological effects like reducing inflammation (98.76 % ± 0.065), fighting free radicals (99.12 % ± 0.027), and being able to inhibit the human coronavirus 229 E with a selective index of 27.9 were observed. The maximum viral inhibitory activity was detected during the adsorption stage. Anti-human liver and colon carcinomas that exceeded Doxorubicin with very low cytotoxicity against normal cell lines were detected. C-PC is an unstable protein that could be degraded in the yoghurt during storage. Therefore, phytosome encapsulation can effectively stabilize C-PC (particle size 44.50 ± 12 nm and zeta-potential -32.4 ± 5 mV) and protect it from the acidic environment of the yoghurt. The produced yoghurt showed the desired physicochemical and functional properties and overall acceptance. The results prove that C-PC from spirulina algae is a renewable source of dyes. The encapsulation process using phytosomes gave it high stability against environmental influences, and therefore, it can be applied in the food and pharmaceutical industries in the future.
PubMed: 38912514
DOI: 10.1016/j.heliyon.2024.e31642