-
Water Research Oct 2023Vinyl chloride (VC) is a dominant carcinogenic residual in many aged chlorinated solvent plumes, and it remains a huge challenge to clean it up. Zerovalent iron (ZVI) is...
Vinyl chloride (VC) is a dominant carcinogenic residual in many aged chlorinated solvent plumes, and it remains a huge challenge to clean it up. Zerovalent iron (ZVI) is an effective reductant for many chlorinated compounds but shows low VC removal efficiency at field scale. Amendment of ZVI with a carbonaceous material may be used to both preconcentrate VC and facilitate redox reactions. In this study, nitrogen-doped graphene (NG) produced by a simple co-pyrolysis method using urea as nitrogen (N) source, was tested as a catalyst for VC reduction by nanoscale ZVI (nZVI). The extent of VC reduction to ethylene in the presence of 2 g/L of nZVI was less than 1% after 3 days, and barely improved with the addition of 4 g/L of graphene. In contrast, with amendment of nZVI with NG produced at pyrolysis temperature (PT) of 950 °C, the VC reduction extent increased more than 10-fold to 69%. The reactivity increased with NG PT increasing from 400 °C to an optimum at 950 °C, and it increased linearly with NG loadings. Interestingly, N dosage had little effect on reactivity if NG was produced at PT of 950 °C, while a positive correlation was observed for NG produced at PT of 600 °C. XPS and Raman analyses revealed that for NG produced at lower PT (<800 °C) mainly the content of pyridine-N-oxide (PNO) groups correlates with reactivity, while for NG produced at higher PT up to 950 °C, reactivity correlates mainly with N induced structural defects in graphene. The results of quenching and hydrogen yield experiments indicated that NG promote reduction of VC by storage of atomic hydrogen, thus increasing its availability for VC reduction, while likely also enabling electron transfer from nZVI to VC. Overall, these findings demonstrate effective chemical reduction of VC by a nZVI-NG composite, and they give insights into the effects of N doping on redox reactivity and hydrogen storage potential of carbonaceous materials.
Topics: Vinyl Chloride; Graphite; Catalysis; Hydrogen; Iron; Nitrogen
PubMed: 37660466
DOI: 10.1016/j.watres.2023.120535 -
Polymers Aug 2023The constant change in microplastics (MP) due to exposure to environmental conditions leads to physical and chemical changes that enhance their ability to transport...
The constant change in microplastics (MP) due to exposure to environmental conditions leads to physical and chemical changes that enhance their ability to transport other pollutants, increasing the concern about their widespread presence in the environment. This work aimed to simulate the aging process of six MP (polyamide 6, unplasticized polyvinyl chloride, low-density polyethylene, polystyrene, polyethylene-co-vinyl acetate, polypropylene) in freshwater and seawater ecosystems at laboratory scale and evaluate its effects through optical microscope observation, Fourier transform infrared spectroscopy-Attenuated Total Reflectance (FTIR-ATR), Raman spectroscopy, and thermal gravimetric analysis (TGA). Through a combined experimental study of aged MP, the degradation by UV interaction was evidenced by the appearance of new infrared bands in the FTIR spectra assigned to ketones and hydroxyl groups. While Raman analysis and microscope images reveal the appearance of pores, wrinkles, and roughness in the MP surfaces. Variations in the temperature of the maximum weight loss of the MP were observed in the TGA analysis. The adsorption of chlorpyrifos (CPF), a common pesticide widely used in agriculture, by the pristine and aged MP was also studied. The highest affinity for CPF was observed for pristine LDPE and the lowest for PP. The batch adsorption studies revealed an increase in adsorption capacity as a consequence of the aging process for both MP. These results proved that the weathering effects caused changes in the behavior of MP, namely in the interaction with other pollutants.
PubMed: 37631527
DOI: 10.3390/polym15163468 -
Antibiotics (Basel, Switzerland) Aug 2023Ammonium group containing polymers possess inherent antimicrobial properties, effectively eliminating or preventing infections caused by harmful microorganisms. Here,...
Ammonium group containing polymers possess inherent antimicrobial properties, effectively eliminating or preventing infections caused by harmful microorganisms. Here, homopolymers based on monomers containing ammonium groups were synthesized via Reversible Addition Fragmentation Chain Transfer Polymerization (RAFT) and evaluated as potential antibacterial agents. The antimicrobial activity was evaluated against Gram-positive ( and ) and Gram-negative bacteria ( and ). Three polymers, poly(diallyl dimethyl ammonium chloride), poly([2-(methacryloyloxy)ethyl]trimethylammonium chloride), and poly(vinyl benzyl trimethylammonium chloride), were examined to explore the effect of molecular weight (10 kDa, 20 kDa, and 40 kDa) on their antimicrobial activity and toxicity to mammalian cells. The mechanisms of action of the polymers were investigated with dye-based assays, while Scanning Electron Microscopy (SEM) showed collapsed and fused bacterial morphologies due to the interactions between the polymers and components of the bacterial cell envelope, with some polymers proving to be bactericidal and others bacteriostatic, while being non-hemolytic. Among all the homopolymers, the most active, non-Gram-specific polymer was poly([2-(methacryloyloxy)ethyl]trimethylammonium chloride), with a molecular weight of 40 kDa, with minimum inhibitory concentrations between 16 and 64 µg/mL, showing a bactericidal mode of action mediated by disruption of the cytoplasmic membrane. This homopolymer could be useful in biomedical applications such as surface dressings and in areas such as eye infections.
PubMed: 37627740
DOI: 10.3390/antibiotics12081320 -
Environmental Science & Technology... Aug 2023On February 3, 2023, a train carrying numerous hazardous chemicals derailed in East Palestine, OH, spurring temporary evacuation of residents and a controlled burn of...
On February 3, 2023, a train carrying numerous hazardous chemicals derailed in East Palestine, OH, spurring temporary evacuation of residents and a controlled burn of some of the hazardous cargo. Residents reported health symptoms, including headaches and respiratory, skin, and eye irritation. Initial data from U.S. Environmental Protection Agency (EPA) stationary air monitors indicated levels of potential concern for air toxics based on hazard quotient calculations. To provide complementary data, we conducted mobile air quality sampling on February 20 and 21 using proton transfer reaction-mass spectrometry. Measurements were taken at 1 s intervals along routes designed to sample both close to and farther from the derailment. Mobile air monitoring indicated that average concentrations of benzene, toluene, xylenes, and vinyl chloride were below minimal risk levels for intermediate and chronic exposures, similar to EPA stationary monitoring data. Levels of acrolein were high relative to those of other volatile organic compounds, with spatial analyses showing levels in East Palestine up to 6 times higher than the local rural background. Nontargeted analyses identified levels of additional unique compounds above background levels, some displaying spatiotemporal patterns similar to that of acrolein and others exhibiting distinct hot spots. These initial findings warrant follow-up mobile air quality monitoring to characterize longitudinal exposure and risk levels.
PubMed: 37577363
DOI: 10.1021/acs.estlett.3c00324 -
Heliyon Aug 2023This study aimed to comprehensively evaluate the health risk of exposure to various vapors and fumes in a factory of automobile manufacturing. This study was performed...
This study aimed to comprehensively evaluate the health risk of exposure to various vapors and fumes in a factory of automobile manufacturing. This study was performed in 2021 on 115 workers. Vapors and fumes were gathered by the adsorbent tubes of activated charcoal and mixed cellulose esters (MCE) membrane filter, respectively. The flow rate for vapors and fumes were between 0.05 and 0.20 L per min and 1 to 4 L per min, respectively. After preparing, samples were analyzed. To assess the non-cancer and cancer risk of the pollutants, the method proposed environmental protection agency (EPA) was applied. The total concentration of copper (1.031 ppm), manganese (0.114), and 2-butoxyethanol (91.767 ppm) were found to be higher than The threshold limit values (TLVs). The values of non-cancer risk (HQ) due to exposure to vapors of benzene (6.583), toluene (1.396), ethyl benzene (1.212), xylene (31.148), 2-butoxyethanol (89.302), 2-propanol (4.695), 1,2,3-trimethylbenzene (1.923), copper (2.336), manganese (715.82), aluminum (3.772), and chromium (107.066) were higher than the acceptable limit. Moreover, the estimated LCR for benzene (2.15 × 10), ethyl benzene (3.97 × 10), vinyl chloride (1.25 × 10), and chromium (2.11 × 10) were higher than the threshold risk level set by EPA. It is emphasized that preventive measures are performed.
PubMed: 37576203
DOI: 10.1016/j.heliyon.2023.e18583 -
Environmental Science and Ecotechnology Jan 2024Electro-bioremediation offers a promising approach for eliminating persistent pollutants from groundwater since allows the stimulation of biological dechlorinating...
Electro-bioremediation offers a promising approach for eliminating persistent pollutants from groundwater since allows the stimulation of biological dechlorinating activity, utilizing renewable electricity for process operation and avoiding the injection of chemicals into aquifers. In this study, a two-chamber microbial electrolysis cell has been utilized to achieve both reductive and oxidative degradation of tetrachloroethane (TeCA). By polarizing the graphite granules cathodic chamber at -650 mV vs the standard hydrogen electrode and employing a mixed metal oxide (MMO) counter electrode for oxygen production, the reductive and oxidative environment necessary for TeCA removal has been established. Continuous experiments were conducted using two feeding solutions: an optimized mineral medium for dechlorinating microorganisms, and synthetic groundwater containing sulphate and nitrate anions to investigate potential side reactions. The bioelectrochemical process efficiently reduced TeCA to a mixture of -dichloroethylene, vinyl chloride, and ethylene, which were subsequently oxidized in the anodic chamber with removal efficiencies of 37 ± 2%, 100 ± 4%, and 100 ± 5%, respectively. The introduction of synthetic groundwater with nitrate and sulphate stimulated reductions in these ions in the cathodic chamber, leading to a 17% decrease in the reductive dechlorination rate and the appearance of other chlorinated by-products, including -dichloroethylene and 1,2-dichloroethane (1,2-DCA), in the cathode effluent. Notably, despite the lower reductive dechlorination rate during synthetic groundwater operation, aerobic dechlorinating microorganisms within the anodic chamber completely removed VC and 1,2-DCA. This study represents the first demonstration of a sequential reductive and oxidative bioelectrochemical process for TeCA mineralization in a synthetic solution simulating contaminated groundwater.
PubMed: 37560753
DOI: 10.1016/j.ese.2023.100309 -
Physiological Reports Aug 2023Nitric oxide (NO) contributes to blood pressure (BP) regulation via its vasodilatory and anti-inflammatory properties. We and others previously reported sex differences...
Nitric oxide (NO) contributes to blood pressure (BP) regulation via its vasodilatory and anti-inflammatory properties. We and others previously reported sex differences in BP in normotensive and hypertensive rat models where females have lower BP than age-matched males. As females are known to have greater NO bioavailability than age-matched males, the current study was designed to test the hypothesis that anesthetized female normotensive Wistar Kyoto rats (WKY) are more responsive to acute NOS inhibition-induced increases in BP compared to male WKY. Twelve-week-old male and female WKY were randomized to infusion of the nonspecific NOS inhibitor N -nitro-L-arginine methyl ester (L-NAME, 1 mg/kg/min) or selective NOS1 inhibition with vinyl-L-NIO (VNIO, 0.5 mg/kg/min) for 60 min. Mean arterial BP, glomerular filtration rate (GFR), urine volume, and electrolyte excretion were assessed before, and during L-NAME or VNIO infusion. L-NAME and VNIO significantly increased BP in both sexes; however, the increase in BP with L-NAME infusion was greater in females versus males compared to baseline BP values. Acute infusion of neither L-NAME nor VNIO for 60 min altered GFR in either sex. However, urine volume, sodium, chloride and potassium excretion levels increased comparably in male and female WKY with L-NAME and VNIO infusion. Our findings suggest sex differences in BP responses to acute non-isoform-specific NOS inhibition in WKY, with females being more responsive to L-NAME-induced elevations in BP relative to male WKY. However, sex differences in the BP response did not coincide with sex differences in renal hemodynamic responses to acute NOS inhibition.
Topics: Animals; Female; Male; Rats; Blood Pressure; Enzyme Inhibitors; Hypertension; Hypotension; NG-Nitroarginine Methyl Ester; Nitric Oxide; Nitric Oxide Synthase; Rats, Inbred WKY
PubMed: 37549936
DOI: 10.14814/phy2.15771 -
Supramolecular chemistry enables vat photopolymerization 3D printing of novel water-soluble tablets.International Journal of Pharmaceutics Aug 2023Vat photopolymerization has garnered interest from pharmaceutical researchers for the fabrication of personalised medicines, especially for drugs that require high...
Vat photopolymerization has garnered interest from pharmaceutical researchers for the fabrication of personalised medicines, especially for drugs that require high precision dosing or are heat labile. However, the 3D printed structures created thus far have been insoluble, limiting printable dosage forms to sustained-release systems or drug-eluting medical devices which do not require dissolution of the printed matrix. Resins that produce water-soluble structures will enable more versatile drug release profiles and expand potential applications. To achieve this, instead of employing cross-linking chemistry to fabricate matrices, supramolecular chemistry may be used to impart dynamic interaction between polymer chains. In this study, water-soluble drug-loaded printlets (3D printed tablets) are fabricated via digital light processing (DLP) 3DP for the first time. Six formulations with varying ratios of an electrolyte acrylate monomer, [2-(acryloyloxy)ethyl]trimethylammonium chloride (TMAEA), and a co-monomer, 1-vinyl-2-pyrrolidone (NVP), were prepared to produce paracetamol-loaded printlets. H NMR spectroscopy analysis confirmed the integration of TMAEA and NVP in the polymer, and residual TMAEA monomers were found to be present only in trace amounts (0.71 - 1.37 %w/w). The apparent molecular mass of the photopolymerised polymer was found to exceed 300,000 Da with hydrodynamic radii of 15 - 20 nm, estimated based on H DOSY NMR measurements The loaded paracetamol was completely released from the printlets between 45 minutes to 5 hours. In vivo single-dose acute toxicity studies in rats suggest that the printlets did not cause any tissue damage. The findings reported in this study represent a significant step towards the adoption of vat photopolymerization-based 3DP to produce personalised medicines.
Topics: Animals; Rats; Acetaminophen; Technology, Pharmaceutical; Printing, Three-Dimensional; Polymers; Drug Liberation; Tablets
PubMed: 37532009
DOI: 10.1016/j.ijpharm.2023.123286 -
Toxics Jul 2023Glitter particles are considered a model of microplastics, which are used in a wide range of products. In this study, we evaluated the toxicity of two types of glitter...
Glitter particles are considered a model of microplastics, which are used in a wide range of products. In this study, we evaluated the toxicity of two types of glitter (green and white, with distinct chemical compositions) dispersions on the embryonic development of the sea urchins , , and the mussel . The Toxicity Identification and Evaluation (TIE) approach was used to identify possible chemicals related to toxicity. Glitter dispersions were prepared using 0.05% ethanol. The tested dispersions ranged from 50 to 500 mg/L. The white glitter was composed of a vinyl chloride-methyl acrylate copolymer. The effective concentrations of green glitter to 50% embryos (EC50) were 246.1 (235.8-256.4) mg/L to , 23.0 (20.2-25.8) mg/L to and 105.9 (61.2-150.2) mg/L, whereas the EC50 of white glitter to was 272.2 (261.5-282.9) mg/L. The EC50 for could not be calculated; however, the lowest effect concentration was 10 mg/L-that was the lowest concentration tested. The filtered suspension of green glitter had Ag levels exceeding the legal standards for marine waters. TIE showed that metals, volatiles, and oxidant compounds contribute to toxicity. The results showed that glitter may adversely affect marine organisms; however, further studies are necessary to determine its environmental risks.
PubMed: 37505582
DOI: 10.3390/toxics11070617 -
Journal of Functional Biomaterials Jun 2023Medical gloves, along with masks and gowns, serve as the initial line of defense against potentially infectious microorganisms and hazardous substances in the health... (Review)
Review
Medical gloves, along with masks and gowns, serve as the initial line of defense against potentially infectious microorganisms and hazardous substances in the health sector. During the COVID-19 pandemic, medical gloves played a significant role, as they were widely utilized throughout society in daily activities as a preventive measure. These products demonstrated their value as important personal protection equipment (PPE) and reaffirmed their relevance as infection prevention tools. This review describes the evolution of medical gloves since the discovery of vulcanization by Charles Goodyear in 1839, which fostered the development of this industry. Regarding the current market, a comparison of the main properties, benefits, and drawbacks of the most widespread types of sanitary gloves is presented. The most common gloves are produced from natural rubber (NR), polyisoprene (IR), acrylonitrile butadiene rubber (NBR), polychloroprene (CR), polyethylene (PE), and poly(vinyl chloride) (PVC). Furthermore, the environmental impacts of the conventional natural rubber glove manufacturing process and mitigation strategies, such as bioremediation and rubber recycling, are addressed. In order to create new medical gloves with improved properties, several biopolymers (e.g., poly(vinyl alcohol) and starch) and additives such as biodegradable fillers (e.g., cellulose and chitin), reinforcing fillers (e.g., silica and cellulose nanocrystals), and antimicrobial agents (e.g., biguanides and quaternary ammonium salts) have been evaluated. This paper covers these performance-enhancing materials and describes different innovative prototypes of gloves and coatings designed with them.
PubMed: 37504844
DOI: 10.3390/jfb14070349