-
Thin-film lithium niobate-based electro-optic comb cloning for self-homodyne coherent communication.Optics Letters Jun 2024As the optical communication industry advances, metropolitan area networks (MANs) and radio access networks (RANs) are extensively deployed on a large scale, demanding...
As the optical communication industry advances, metropolitan area networks (MANs) and radio access networks (RANs) are extensively deployed on a large scale, demanding energy-efficient integrated light sources and simplified digital signal processing (DSP) technologies. The emergence of thin-film lithium niobate (TFLN) has given rise to high-performance, energy-efficient on-chip modulators, making on-chip optical frequency comb (OFC) more appealing. Owing to the phase uniformity and stability of this chip-scale device, it has been possible to eliminate the carrier frequency phase estimation (CPE) in DSP stacks using comb-clone-enabled self-homodyne detection. Here we report the first use, to our knowledge, of a TFLN on-chip electro-optic (EO) frequency comb to realize comb cloning and self-homodyne coherent detection. We transmit three optical pilot tones and eight data channels encoded with 20 Gbaud polarization-multiplexed 16-ary quadrature amplitude modulation (PM-16-QAM) over 10 km and 80 km standard single-mode fibers. The bit error ratios (BERs) of the eight channels reach below 10, a result made possible by our on-chip comb. The scalability and mass producibility of on-chip EO combs, combined with the simplified DSP, show potential in our proposed fifth-generation (5G) RAN and MAN transmission scheme.
PubMed: 38824372
DOI: 10.1364/OL.527403 -
Optics Letters Jun 2024Lithium niobate (LN) photonics has gained significant interest for their distinct material properties. However, achieving monolithically integrated photodetectors on...
Lithium niobate (LN) photonics has gained significant interest for their distinct material properties. However, achieving monolithically integrated photodetectors on lithium niobate on an insulator (LNOI) platform for communication wavelengths remains a challenge due to the large bandgap and extremely low electrical conductivity of LN material. A two-dimensional (2D) material photodetector is an ideal solution for LNOI photonics with a strong light-matter interaction and simple integration technique. In this work, a van der Waals heterostructure photodiode composed of a p-type black phosphorus layer and an n-type MoS layer is successfully demonstrated for photodetection at communication wavelengths on a LNOI platform. The LNOI waveguide-integrated BP-MoS photodetector exhibits a dark current as low as 0.21 nA and an on/off ratio exceeding 200 under zero voltage bias with an incident power of 13.93 µW. A responsivity as high as 1.46 A/W is achieved at -1 V bias with a reasonable dark current around 2.33 µA. With the advantages of high responsivity, low dark current, and simple fabrication process, it is promising for the monolithically integrated photodetector application for LNOI photonic platforms at communication wavelengths.
PubMed: 38824353
DOI: 10.1364/OL.522343 -
Optics Letters Jun 2024We demonstrate a monolithic tunable dual-wavelength laser fabricated on erbium-doped lithium niobate on an insulator (Er:LNOI). The dual-wavelength laser enables...
We demonstrate a monolithic tunable dual-wavelength laser fabricated on erbium-doped lithium niobate on an insulator (Er:LNOI). The dual-wavelength laser enables independent tuning with a continuously linear electro-optic (EO)-modulated tuning range of 11.875 GHz at a tuning efficiency of 0.63 pm/V. Tunable microwave generation within 50 GHz with a maximum extinction ratio of 35 dB is experimentally demonstrated by further exploring the charge accumulation effect in LNOI. The monolithic design of this work paves the way for microscale integration of laser devices, presenting significant prospects in photonics research and applications.
PubMed: 38824317
DOI: 10.1364/OL.522774 -
Optics Letters Jun 2024Mode converters, crucial elements within photonic integrated circuits (PICs) designed for multimode optical transmission and switching systems, present a challenge due...
Mode converters, crucial elements within photonic integrated circuits (PICs) designed for multimode optical transmission and switching systems, present a challenge due to their bulky structures in thin-film lithium niobate (TFLN) integrated platforms, which are incompatible with the compact and efficient nature desired for dense PICs. In this work, we propose TE-TE, TE-TE, and TE-TE mode converters in shallowly etched TFLN, within small footprints. The experimental results show that the insertion loss is 0.4 dB, 0.6 dB, and 0.5 dB for the compact TE-TE, TE-TE, and TE-TE mode converters, respectively, and these devices can be operated within a wide 1 dB bandwidth (BW) over 100 nm. This work facilitates the development of low-loss, broadband, and compact monolithically integrated photonic devices for future multimode communication networks in TFLN integrated platforms.
PubMed: 38824302
DOI: 10.1364/OL.524739 -
Journal of Colloid and Interface Science May 2024Lithium-sulfur (Li-S) batteries exhibit superior theoretical capacity and energy density but are still hindered by the sluggish redox conversion kinetic of lithium...
Lithium-sulfur (Li-S) batteries exhibit superior theoretical capacity and energy density but are still hindered by the sluggish redox conversion kinetic of lithium polysulfides arising from the significant desolvation barrier, especially under high current density or low-temperature environments. Herein, a two-dimensional (2D) porous graphitic phase carbon nitride/MXene (CN-MX) heterostructure with intrinsic defects was designed via electrostatic adherence and in-situ thermal polycondensation. In the design, the defect-rich CN with abundant catalytic activity and porous structure could efficiently facilitate the lithium polysulfides capture, the dissociation of solvated lithium-ion (Li), and fast Li diffusion. Concurrently, 2D MXene nanosheets with high electronic conductivity could act as charge transport channels and provide electrochemical active sites for sulfur redox reactions. The Li-S cells with CN-MX heterostructure modified separator demonstrated uncommon rate performance (945 mAh/g at 4.0 C) and satisfactory areal capacity (5.5 mAh cm at 0.2 C). Most remarkably, even at 0 °C, the assembled Li-S batteries performed favorable cycle stability (91.6% capacity retention after 100 cycles at 0.5 C) and outstanding rate performance (695 mAh/g at 2.0 C), and superior high loading performance (5.1 mAh cm at 0.1 C). This work offers exciting new insights to enable Li-S batteries to operate in extreme environments.
PubMed: 38823110
DOI: 10.1016/j.jcis.2024.05.026 -
ChemSusChem Jun 2024Affordable clean energy is one of the major sustainable development goals that can transform our world. At present, researchers are working to develop cheap electrode...
Affordable clean energy is one of the major sustainable development goals that can transform our world. At present, researchers are working to develop cheap electrode materials to develop energy storage devices, the Lithium-sulfur (Li-S) battery is considered a promising energy storage device owing to its excellent theoretical specific capacity and energy density. Herein, utilizing the ramie degumming waste liquid as raw materials, after freeze-drying and high-temperature calcination, a sustainable and cost-effective three-dimensional (3D) porous nitrogen-doped ramie carbon (N-RC) was synthesized. The N-RC calcined at 800 °C (N-RC-800) shows a superior high specific surface area of 1491.85 m2·g-1 and a notable high pore volume of 0.90 cm3·g-1. When employed as a sulfur host, the S@N-RC-800 cathode illustrates excellent initial discharge capacity (1120.6 mAh·g-1) and maintains a reversible capacity of 625.4 mAh·g-1 after 500 cycles at 1 C. Simultaneously, the S@N-RC-800 cathode also shows excellent coulombic efficiency and ideal rate performance. Such exceptional electrochemical performance of S@N-RC-800 can be primarily attributable to N-RC's high specific surface area, high porosity, and abundant polar functional groups. This green and low-cost synthesis strategy offers a new avenue for harnessing the potential of waste biomass in the context of clean energy storage.
PubMed: 38823005
DOI: 10.1002/cssc.202400576 -
Environmental Science & Technology Jun 2024Lithium (Li) is an important resource that drives sustainable mobility and renewable energy. Its demand is projected to continue to increase in the coming decades....
Lithium (Li) is an important resource that drives sustainable mobility and renewable energy. Its demand is projected to continue to increase in the coming decades. However, the risk of Li pollution has also emerged as a global concern. Here, we investigated the pollution characteristics, sources, exposure levels, and associated health risks of Li in the Jinjiang River basin, the largest area for LiCO production in China. Our results revealed the dominant role of Li extraction activities in the pollution of the river, with over 95% of dissolved Li in downstream river water being emitted from this source. Moreover, the Li concentration in aquatic plants (i.e., water hyacinth) and animals (i.e., fish) significantly increased from upstream to downstream areas, indicating a significant risk to local aquatic ecosystems. More importantly, our study found that local residents were suffering potential chronic noncarcinogenic health risks primarily from consuming contaminated water and vegetables. We also investigated the pollution characteristics of associated elements present in Li ores (e.g., Rb, Cs, Ni, and F). By uncovering the remarkable impact of Li extraction activities on the Li content in ecosystems for the first time, our study emphasizes the importance of evaluating Li pollution from Li-related industrial activities, including mining, extraction, and recovery.
PubMed: 38822815
DOI: 10.1021/acs.est.4c00225 -
Small (Weinheim An Der Bergstrasse,... Jun 2024Photo-rechargeable batteries (PRBs) can provide a compact solution to power autonomous smart devices located at remote sites that cannot be connected with the grid. The...
Photo-rechargeable batteries (PRBs) can provide a compact solution to power autonomous smart devices located at remote sites that cannot be connected with the grid. The study reports the Ruddlesden-Popper (RP) metal halide perovskite (MHP) and molybdenum disulfide (MoS) hybrid heterojunction-based photocathodes for Li-ion photo-rechargeable battery (Li-PRB) applications. Hybrid Lithium-ion batteries (LIBs) have demonstrated an average discharge specific capacity of 144.46 and 129.17 mAhg for 50 cycles when operating at 176 and 294 mAg, respectively compared to the pristine LIBs which have shown specific capacity of 37.48 and 25.60 mAhg under similar conditions. Hybrid Li-PRB has achieved an average dark discharge specific capacities of 128.66 mAhg (capacity retention: 96.56%) which enhanced to 180.67 mAhg under illumination (capacity retention: 97.39%; photo-enhancement: 40.42%) at 64 mAg. Excellent performance of hybrid Li-PRB is attributed to the formation of type-II heterojunction that leads to improved crystallinity and film morphology. The PRB has demonstrated a high photo conversion and storage efficiency (PC-SE) of 0.52% under standard 1 Sun illumination, which outperforms other previously reported MHP based LIBs and PRBs. This work provides a novel approach of harnessing the potential of MHPs for PRBs and offers new avenues for MHP photocathodes for various applications beyond PRBs.
PubMed: 38822720
DOI: 10.1002/smll.202401350 -
Small (Weinheim An Der Bergstrasse,... Jun 2024Phosphorus is regarded as a promising material for high-performance lithium-ion batteries (LIBs) due to its high theoretical capacity, appropriate lithiation potential,...
Phosphorus is regarded as a promising material for high-performance lithium-ion batteries (LIBs) due to its high theoretical capacity, appropriate lithiation potential, and low lithium-ion diffusion barrier. Phosphorus/carbon composites (PC) are engineered to serve as high-capacity high-rate anodes; the interaction between phosphorus and carbon, long-term capacity retention, and safety problems are important issues that must be well addressed simultaneously. Herein, an in situ polymerization approach to fabricate a poly-melamine-hybridized (pMA) phosphorus/carbon composite (pMA-PC) is employed. The pMA hybridization enhances the density and electrical conductivity of the PC, improves the structural integrity, and facilitates stable electron transfer within the pMA-PC composite. Moreover, the pMA-PC composite exhibits efficient adsorption of lithium polysulfides, enabling stable transport of Li ions. Therefore, the pMA-PC anode demonstrates a high specific charging capacity of 1,381 mAh g at 10 A g, and a great capacity retention of 86.7% at 1 A g over 500 cycles. The synergistic effect of phosphorus and nitrogen further confers excellent flame retardant properties to the pMA-PC anode, including self-extinguishing in 2.5 s, and a much lower combustion temperature than PC. The enhanced capacity and safety performance of pMA-PC show potential in future high-capacity and high-rate LIBs.
PubMed: 38822719
DOI: 10.1002/smll.202402483 -
Small (Weinheim An Der Bergstrasse,... Jun 2024Surface modification of Cu current collectors (CCs) is proven to be an effective method for protecting lithium metal anodes. However, few studies have focused on the...
Surface modification of Cu current collectors (CCs) is proven to be an effective method for protecting lithium metal anodes. However, few studies have focused on the quality and efficiency of modification layers. Herein, a novel home-made filtered cathode vacuum arc (FCVA) co-deposition system with high modification efficiency, good repeatability and environmental friendliness is proposed to realize the wide range regulation of film composition, structure and performance. Through this system, ZnMgTiAl quaternary alloy films, which have good affinity with Li are successfully constructed on Cu CCs, and the fully enhanced electrochemical performances are achieved. Symmetrical cells constructed with modified CCs maintained a fairly low voltage hysteresis of only 13 mV after 2100 h at a current density of 1 mA cm. In addition, the capacity retention rate is as high as 75.0% after 100 cycles in the full cells. The influence of alloy films on the dynamic evolution process of constructing stable artificial solid electrolyte interphase (SEI) layer is revealed by in situ infrared (IR) spectroscopy. This work provides a promising route for designing various feasible modification films for LMBs, and it displays better industrial application prospects than the traditional chemical methods owing to the remarkable controllability and scale-up capacity.
PubMed: 38822717
DOI: 10.1002/smll.202402752