-
Scientific Reports Nov 2022One-step direct patterning of high definition conductive tracks in textiles is realized through laser direct writing in combination with a silver organometallic ink...
One-step direct patterning of high definition conductive tracks in textiles is realized through laser direct writing in combination with a silver organometallic ink developed in-house. Photoreduction, nano-crystallization, and sintering are accomplished in one pass under the irradiation of a CW green laser light (λ = 532 nm) at moderate intensities (I ≥ 95 mW/mm). By tailoring the surface tension and viscosity of the ink, high-definition conductive tracks are formed in weft-knitted polyester-Spandex composite fabrics, well-following the laser's profile with negligible coffee stain effect. Length resistance as low as 4 Ω/cm is measured and anisotropy of the gauge factor as high as 25 is achieved. The metallized fabric exhibits reversible and hysteresis-free electromechanical responses subject to high strains. Durability assessment qualifies that the as-metallized strain sensors are able to sustain their performance for over 5000 stretch/release cycles, demonstrating its potential applications in biaxial strain sensing and interactive smart textiles.
Topics: Textiles; Electric Conductivity; Polyurethanes; Polyesters; Wearable Electronic Devices
PubMed: 36414763
DOI: 10.1038/s41598-022-24676-7 -
International Journal of Environmental... Sep 2021Several different dental implant microgeometries have been investigated in the literature for use in low-density bone sites. The polyurethane solid rigid blocks...
An In Vitro Analysis on Polyurethane Foam Blocks of the Insertion Torque (IT) Values, Removal Torque Values (RTVs), and Resonance Frequency Analysis (RFA) Values in Tapered and Cylindrical Implants.
BACKGROUND
Several different dental implant microgeometries have been investigated in the literature for use in low-density bone sites. The polyurethane solid rigid blocks represent an optimal in vitro study model for dental implants, because their composition is characterized by symmetrical linear chains of monomers of hexa-methylene sequences producing a self-polymerization process. The aim of the present investigation was to evaluate the primary stability of cylindrical and tapered implants positioned into low-density polyurethane solid rigid blocks.
MATERIALS AND METHODS
Two different macrogeometries, cylindrical (4 mm diameter and 10 mm length) and tapered dental implants (4.20 mm diameter and 10 mm length), were investigated in the present study. The implants were inserted into 10 PCF and 20 PCF polyurethane blocks, with and without an additional cortical layer. The insertion torque (IT) values, the removal torque values (RTVs), and the resonance frequency analysis (RFA) values were measured and recorded.
RESULTS
A total of 80 sites were tested, and a significant increased primary stability (PS) was detected in favour of tapered dental implants when compared to cylindrical implants in all experimental conditions ( < 0.05). Higher IT, RT, and RFA values were measured in tapered implants in 10 and 20 PCF polyurethane blocks, both with and without the additional cortical layer.
CONCLUSIONS
Both implants showed sufficient primary stability in poor density substrates, while, on the other hand, the tapered microgeometry showed characteristics that could also lead to clinical application in low-density posterior maxillary sites, even with a drastically decreased bone cortical component.
Topics: Bone Density; Dental Implants; Maxilla; Polyurethanes; Resonance Frequency Analysis; Torque
PubMed: 34501824
DOI: 10.3390/ijerph18179238 -
Microbiology Spectrum Jun 2023Plastic wastes have been recognized as the most common and durable marine contaminants, which are not only found in the shallow water, but also on the sea floor....
Plastic wastes have been recognized as the most common and durable marine contaminants, which are not only found in the shallow water, but also on the sea floor. However, whether deep-sea microorganisms have evolved the capability of degrading plastic remains elusive. In this study, a deep-sea bacterium Bacillus velezensis GUIA was found to be capable of degrading waterborne polyurethane. Transcriptomic analysis showed that the supplement of waterborne polyurethane upregulated the expression of many genes related to spore germination, indicating that the presence of plastic had effects on the growth of strain GUIA. In addition, the supplement of waterborne polyurethane also evidently upregulated the expressions of many genes encoding lipase, protease, and oxidoreductase. Liquid chromatography-mass spectrometry (LC-MS) results showed that potential enzymes responsible for plastic degradation in strain GUIA were identified as oxidoreductase, protease, and lipase, which was consistent with the transcriptomic analysis. In combination of expression and degradation assays as well as Fourier transform infrared (FTIR) analysis, we demonstrated that the oxidoreductase Oxr-1 of strain GUIA was the key degradation enzyme toward waterborne polyurethane. Moreover, the oxidoreductase Oxr-1 was also shown to degrade the biodegradable polybutylene adipate terephthalate (PBAT) film indicating its wide application potential. The widespread and indiscriminate disposal of plastics inevitably leads to environmental pollution. The secondary pollution by current landfill and incineration methods causes serious damage to the atmosphere, land, and rivers. Therefore, microbial degradation is an ideal way to solve plastic pollution. Recently, the marine environment is becoming a hot spot to screen microorganisms possessing potential plastic degradation capabilities. In this study, a deep-sea strain was shown to degrade both waterborne polyurethane and biodegradable PBAT film. The FAD-binding oxidoreductase Oxr-1 was demonstrated to be the key enzyme mediating plastic degradation. Our study not only provided a good candidate for developing bio-products toward plastic degradation but also paved a way to investigate the carbon cycle mediated by plastic degradation in deep-sea microorganisms.
Topics: Polyurethanes; Biodegradation, Environmental; Plastics; Bacteria; Lipase; Endopeptidases; Peptide Hydrolases; Oxidoreductases
PubMed: 36995243
DOI: 10.1128/spectrum.00073-23 -
Journal of Colloid and Interface Science May 2022Acetic acid, a common pollutant present in museums and art galleries, can irreversibly damage works of art. Herein, a sustainable and scalable synthesis of zinc...
HYPOTHESIS
Acetic acid, a common pollutant present in museums and art galleries, can irreversibly damage works of art. Herein, a sustainable and scalable synthesis of zinc oxide-castor oil polyurethane hybrids (ZnO/COPs), to be used as acetic acid removers in the preventive conservation of Cultural Heritage, is reported.
EXPERIMENTS
The adsorption capacities of ZnO/COPs were studied in saturated acetic acid atmosphere, at low acetic acid gas concentration, and inside a wooden crate (naturally emitting acetic acid) representative of those used in the storage deposits of museums and art collections.
FINDINGS
Upon exposure, acetic acid interacts with the castor oil polyurethane and diffuses to the surface of ZnO particles where is stably fixed as zinc acetate crystals. Zinc acetate domains form homogeneously on the surface and are distributed evenly within the ZnO/COPs, thanks to weak interactions between the polyurethane matrix and acetic acid that favour the transport of the acid up to reach the zinc oxide surfaces, resulting in a synergistic effect. The ZnO/COPs composites showed significantly enhanced adsorption capacities of acetic acid surpassing those of the activated carbon benchmark, with the advantage of being easily handled and movable, without the health issues and risks associated to the use of non-confined micro/nano-powders.
Topics: Acetic Acid; Adsorption; Castor Oil; Polyurethanes; Zinc Oxide
PubMed: 35108636
DOI: 10.1016/j.jcis.2022.01.123 -
Scientific Reports May 2024Repair and reconstruction of the myopectineal orifice area using meshes is the mainstay of surgical treatment of inguinal hernias. However, the limitations of existing...
Repair and reconstruction of the myopectineal orifice area using meshes is the mainstay of surgical treatment of inguinal hernias. However, the limitations of existing meshes are becoming increasingly evident in clinical applications; thus, the idea of using three-dimensionally (3D)-printed biological meshes was put forward. According to the current level of the 3D printing technology and the inherent characteristics of biological materials, the direct use of the 3D printing technology for making biological materials into finished products suitable for clinical applications is not yet supported, but synthetic materials can be first printed into 3D form carriers, compounded with biological materials, and finally made into finished products. The purpose of this study was to develop a technical protocol for making 3D-printed biomesh carriers using polyurethane as a raw material. In our study: raw material, polyurethane; weight, 20-30 g/m; weaving method, hexagonal mesh; elastic tension aspect ratio, 2:1; diameters of pores, 0.1-1 mm; surface area, 8 × 12 cm; the optimal printing layer height, temperature and velocity were 0.1 mm, 210-220 °C and 60 mm/s. Its clinical significance lies in: (1) applied to preoperative planning and design a detailed surgical plan; (2) applied to special types of surgery including patients in puberty, recurrent and compound inguinal hernias; (3) significantly improve the efficiency of doctor-patient communication; (4) it can shorten the operation and recovery period by about 1/3 and can save about 1/4 of the cost for patients; (5) the learning curve is significantly shortened, which is conducive to the cultivation of reserve talents.
Topics: Printing, Three-Dimensional; Polyurethanes; Surgical Mesh; Humans; Hernia, Inguinal; Biocompatible Materials; Herniorrhaphy; Materials Testing
PubMed: 38806559
DOI: 10.1038/s41598-024-63000-3 -
Scientific Reports Dec 2022This paper introduces a new approach of testing piezoelectric nanofibers as antibacterial mat. In this work, both Polyvinylidene fluoride (PVDF) and PVDF embedded with...
This paper introduces a new approach of testing piezoelectric nanofibers as antibacterial mat. In this work, both Polyvinylidene fluoride (PVDF) and PVDF embedded with thermoplastic polyurethane nanofibers are synthesized as nanofibers mat via electrospinning technique. Then, such mat is analyzed as piezoelectric material to generate electric voltage under different mechanical excitations. Furthermore, morphological and chemical characteristics have been operated to prove the existence of beta sheets piezoelectricity of the synthesized nanofibers mats. Then, the synthesized nanofibers surfaces have been cyclically stretched and exposed to bacteria specimen. It has been noticed that the generated voltage and the corresponding localized electric field positively affect the growth of bacteria and reduces the formation of K. penomenue samples bacteria colonies. In addition, the effect of both stretching frequency and pulses numbers have been studied on the bacteria count, growth kinetics, and protein leakage. Our contribution here is to introduce an innovative way of the direct impact of the generated electric field from piezoelectric nanofibers on the reduction of bacteria growth, without depending on traditional anti-bacterial nanoparticles. This work can open a new trend of the usability of piezoelectric nanofibers through masks, filters, and wound curing mats within anti-bacterial biological applications.
Topics: Nanofibers; Polyvinyls; Anti-Bacterial Agents; Polyurethanes; Bacteria
PubMed: 36526645
DOI: 10.1038/s41598-022-25212-3 -
Nature Communications Dec 2022The self-healing properties and ionic sensing capabilities of the human skin offer inspiring groundwork for the designs of stretchable iontronic skins. However, from...
The self-healing properties and ionic sensing capabilities of the human skin offer inspiring groundwork for the designs of stretchable iontronic skins. However, from electronic to ionic mechanosensitive skins, simultaneously achieving autonomously superior self-healing properties, superior elasticity, and effective control of ion dynamics in a homogeneous system is rarely feasible. Here, we report a Cl-functionalized iontronic pressure sensitive material (CLiPS), designed via the introduction of Cl-functionalized groups into a polyurethane matrix, which realizes an ultrafast, autonomous self-healing speed (4.3 µm/min), high self-healing efficiency (91% within 60 min), and mechanosensitive piezo-ionic dynamics. This strategy promotes both an excellent elastic recovery (100%) and effective control of ion dynamics because the Cl groups trap the ions in the system via ion-dipole interactions, resulting in excellent pressure sensitivity (7.36 kPa) for tactile sensors. The skin-like sensor responds to pressure variations, demonstrating its potential for touch modulation in future wearable electronics and human-machine interfaces.
Topics: Humans; Wearable Electronic Devices; Ions; Skin; Polyurethanes; Electronics
PubMed: 36509757
DOI: 10.1038/s41467-022-35434-8 -
Journal of Medicine and Life 2020Polyurethane nano- and micro-structures have been studied intensively in the last decade as drug delivery systems for various herbal extracts as well as pure active...
Polyurethane nano- and micro-structures have been studied intensively in the last decade as drug delivery systems for various herbal extracts as well as pure active biological substances. Their biocompatibility, haemocompatibility, safe degradation, and low-cost production are just a few advantages of these materials that were already used in numerous medical applications (catheters, surgical drapes, wound dressing). The primary purposes of this study include obtaining empty polyurethane microstructures and the assessment of their modifications in media with different pH values. A mixture of two aliphatic diisocyanates and an aqueous phase based on a polyether were used during the synthesis process. The size, homogeneity, and surface charge were studied using a Cordouan Technol. Zetasizer, while the pH measurements were conducted with a portable pH Meter Checker®, Hanna Instruments. The results showed the obtaining of an almost homogeneous sample containing microstructures with sizes ranging between 139 and 151 nm, with a pH value of approximately 6.78 and a Zeta potential of 24.6. Expected decreases in microparticles' sizes were observed in all types of media during a 15-days experiment, but the process was accelerated by a low pH when an increase of the Zeta potential value was noticed as well. Our data provide new information about the degradation process of the polyurethane microstructures on the one hand and the drug release rate of these materials when used as drug carriers, on the other hand.
Topics: Drug Carriers; Hydrogen-Ion Concentration; Particle Size; Polyurethanes; Static Electricity
PubMed: 32742513
DOI: 10.25122/jml-2020-0010 -
ACS Applied Materials & Interfaces Jun 2023Tendon disorders are common medical conditions, which can be greatly debilitating as they are often accompanied by great pain and inflammation. The techniques used...
Tendon disorders are common medical conditions, which can be greatly debilitating as they are often accompanied by great pain and inflammation. The techniques used nowadays for the treatment of chronic tendon injuries often involve surgery. However, one critical aspect of this procedure involves the scar tissue, characterized by mechanical properties that vary from healthy tissue, rendering the tendons inclined to reinjury or rupture. Synthetic polymers, such as thermoplastic polyurethane, are of special interest in the tissue engineering field as they allow the production of scaffolds with controlled elastic and mechanical properties, which could guarantee an effective support during the new tissue formation. The aim of this work was the design and the development of tubular nanofibrous scaffolds based on thermoplastic polyurethane and enriched with cerium oxide nanoparticles and chondroitin sulfate. The scaffolds were characterized by remarkable mechanical properties, especially when tubular aligned, reaching values comparable to the ones of the native tendons. A weight loss test was performed, suggesting a degradation in prolonged times. In particular, the scaffolds maintained their morphology and also remarkable mechanical properties after 12 weeks of degradation. The scaffolds promoted the cell adhesion and proliferation, in particular when in aligned conformation. Finally, the systems in vivo did not cause any inflammatory effect, representing interesting platforms for the regeneration of injured tendons.
Topics: Tissue Scaffolds; Chondroitin Sulfates; Polyurethanes; Tissue Engineering; Tendons; Cell Proliferation
PubMed: 37220144
DOI: 10.1021/acsami.3c06144 -
Microbial Biotechnology Feb 2023Global economies depend on the use of fossil-fuel-based polymers with 360-400 million metric tons of synthetic polymers being produced per year. Unfortunately, an... (Review)
Review
Global economies depend on the use of fossil-fuel-based polymers with 360-400 million metric tons of synthetic polymers being produced per year. Unfortunately, an estimated 60% of the global production is disposed into the environment. Within this framework, microbiologists have tried to identify plastic-active enzymes over the past decade. Until now, this research has largely failed to deliver functional biocatalysts acting on the commodity polymers such as polyethylene (PE), polypropylene (PP), polyvinylchloride (PVC), ether-based polyurethane (PUR), polyamide (PA), polystyrene (PS) and synthetic rubber (SR). However, few enzymes are known to act on low-density and low-crystalline (amorphous) polyethylene terephthalate (PET) and ester-based PUR. These above-mentioned polymers represent >95% of all synthetic plastics produced. Therefore, the main challenge microbiologists are currently facing is in finding polymer-active enzymes targeting the majority of fossil-fuel-based plastics. However, identifying plastic-active enzymes either to implement them in biotechnological processes or to understand their potential role in nature is an emerging research field. The application of these enzymes is still in its infancy. Here, we summarize the current knowledge on microbial plastic-active enzymes, their global distribution and potential impact on plastic degradation in industrial processes and nature. We further outline major challenges in finding novel plastic-active enzymes, optimizing known ones by synthetic approaches and problems arising through falsely annotated and unfiltered use of database entries. Finally, we highlight potential biotechnological applications and possible re- and upcycling concepts using microorganisms.
Topics: Plastics; Polymers; Polyurethanes; Fossil Fuels; Biodegradation, Environmental
PubMed: 36099200
DOI: 10.1111/1751-7915.14135