-
Vaccines Jun 2024Introducing new recombinant protein antigens to existing pediatric combination vaccines is important in improving coverage and affordability, especially in low- and...
Evaluating the Compatibility of New Recombinant Protein Antigens (Trivalent NRRV) with a Mock Pentavalent Combination Vaccine Containing Whole-Cell Pertussis: Analytical and Formulation Challenges.
Introducing new recombinant protein antigens to existing pediatric combination vaccines is important in improving coverage and affordability, especially in low- and middle-income countries (LMICs). This case-study highlights the analytical and formulation challenges encountered with three recombinant non-replicating rotavirus vaccine (NRRV) antigens (t-NRRV formulated with Alhydrogel adjuvant, AH) combined with a mock multidose formulation of a pediatric pentavalent vaccine used in LMICs. This complex formulation contained (1) vaccine antigens (i.e., whole-cell pertussis (wP), diphtheria (D), tetanus (T), (Hib), and hepatitis B (HepB), (2) a mixture of aluminum-salt adjuvants (AH and Adju-Phos, AP), and (3) a preservative (thimerosal, TH). Selective, stability-indicating competitive immunoassays were developed to monitor binding of specific mAbs to each antigen, except wP which required the setup of a mouse immunogenicity assay. Simple mixing led to the desorption of t-NRRV antigens from AH and increased degradation during storage. These deleterious effects were caused by specific antigens, AP, and TH. An AH-only pentavalent formulation mitigated t-NRRV antigen desorption; however, the Hib antigen displayed previously reported AH-induced instability. The same rank-ordering of t-NRRV antigen stability (P[8] > P[4] > P[6]) was observed in mock pentavalent formulations and with various preservatives. The lessons learned are discussed to enable future multidose, combination vaccine formulation development with new vaccine candidates.
PubMed: 38932338
DOI: 10.3390/vaccines12060609 -
Viruses Jun 2024Prior research has established the anti-apoptotic effects in insect cell cultures of () hemolymph, as well as the heightened production yields of recombinant proteins...
Prior research has established the anti-apoptotic effects in insect cell cultures of () hemolymph, as well as the heightened production yields of recombinant proteins facilitated by baculovirus vectors in insect cells cultivated in media supplemented with this hemolymph. In this study, we investigated the hemolymph of another Lepidoptera species, (), and observed similar beneficial effects in insect cells cultivated in media supplemented with this natural substance. We observed enhancements in both production yield (approximately 1.5 times higher) and late-stage cell viabilities post-infection (30-40% higher). Storage-protein 2 from (SP2Bm) has previously been identified as one of the abundant hemolymph proteins potentially responsible for the beneficial effects observed after the use of hemolymph-supplemented cell culture media. By employing a dual baculovirus vector that co-expresses the SP2Bm protein alongside the GFP protein, we achieved a threefold increase in reporter protein production compared to a baculovirus vector expressing GFP alone. This study underscores the potential of hemolymph proteins sourced from various Lepidoptera species as biotechnological tools to augment baculovirus vector productivities, whether utilized as natural supplements in cell culture media or as hemolymph-derived recombinant proteins co-expressed by baculovirus vectors.
Topics: Animals; Hemolymph; Recombinant Proteins; Baculoviridae; Insect Proteins; Lepidoptera; Genetic Vectors; Cell Line; Gene Expression; Green Fluorescent Proteins; Bombyx; Culture Media; Moths; Cell Survival
PubMed: 38932236
DOI: 10.3390/v16060944 -
Polymers Jun 2024In this study, a novel branched polyamide 6 has been synthesized via the hydrolytic ring-opening co-polymerization of ε-caprolactam (CPL) and α-Amino-ε-caprolactam...
In this study, a novel branched polyamide 6 has been synthesized via the hydrolytic ring-opening co-polymerization of ε-caprolactam (CPL) and α-Amino-ε-caprolactam (ACL). The NMR characterization proves the existence of a branched chain structure. The rheological test determines that there is a remarkable increase in the melt index (MFR), zero shear rate viscosity, and storage modulus in the low-frequency region. The shear-thinning phenomenon becomes more obvious. The thermal properties tested by differential scanning calorimetry (DSC) show that the melting point and crystallinity of co-polymers decrease with the incorporation of ACL. However, the crystal structure of the samples only exhibits a slight change. When the ACL content in the feed is 1 wt%, the tensile strength and fracture elongation rate of the co-polymers show a significant enhancement.
PubMed: 38932069
DOI: 10.3390/polym16121719 -
Polymers Jun 2024This study aimed to evaluate the flexural strength (FS), surface wear, and optical properties of 3D-printed dental resins subjected to different post-printing...
This study aimed to evaluate the flexural strength (FS), surface wear, and optical properties of 3D-printed dental resins subjected to different post-printing conditions. A total of 240 specimens (2 × 2 × 25 mm³) were 3D-printed using resin materials for permanent (VaresoSmile Crown Plus) VSC and temporary (VaresoSmile Temp) VST restorations. Specimens underwent five post-printing conditions: no post-printing cure; post-cured in a Form Cure curing unit; Visio Beta Vacuum; Ivoclar Targis; or heat-cured (150 °C) for 30 min. Each group of specimens ( = 24) was tested either directly after post-curing, after 24 h of dry storage, or following hydrothermal accelerated aging in boiling water for 16 h. The three-point bending test was used to evaluate the FS. The two-body wear test was performed on 50 disc-shaped specimens ( = 5/group). Surface gloss and translucency were measured for permanent VSC specimens ( = 5/group). SEM/EDS and statistical analyses were performed. The Form Cure device yielded the highest FS and lowest wear depth ( < 0.05). Hydrothermal aging significantly reduced FS. There were no statistical differences in FS and wear values between materials subjected to same post-printing conditions. VSC groups exhibited similar optical properties across different post-printing treatments. Post-printing treatment conditions had a significant impact on the FS and wear of the 3D-printed resin, while optical properties remained unaffected.
PubMed: 38932063
DOI: 10.3390/polym16121713 -
Polymers Jun 2024Herein, we investigate the potential application of a composite consisting of PEDOT:PSS/Graphene, deposited via spray coating on a flexible substrate, as an autonomous...
Herein, we investigate the potential application of a composite consisting of PEDOT:PSS/Graphene, deposited via spray coating on a flexible substrate, as an autonomous conducting film for applications in wearable biosensor devices. The stability of PEDOT:PSS/Graphene is assessed through electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and linear polarization (LP) during exposure to an artificial sweat electrolyte, while scanning electron microscopy (SEM) was employed to investigate the morphological changes in the layer following these. The results indicate that the layers exhibit predominant capacitive behavior in the potential range of -0.3 to 0.7 V vs. Ag/AgCl, with a cut-off frequency of approximately 1 kHz and retain 90% capacity after 500 cycles. Aging under exposure to air for 6 months leads only to a minor increase in impedance, demonstrating potential for storage under non-demanding conditions. However, prolonged exposure (>48 h) to the artificial sweat causes significant degradation, resulting in an impedance increase of over 1 order of magnitude. The observed degradation raises important considerations for the long-term viability of these layers in wearable biosensor applications, prompting the need for additional protective measures during prolonged use. These findings contribute to ongoing efforts to enhance the stability and reliability of conducting materials for biosensors in health care and biotechnology applications.
PubMed: 38932055
DOI: 10.3390/polym16121706 -
Polymers Jun 2024Zinc-ion batteries are promising candidates for large-scale energy storage. The side reactions of the hydrogen evolution reaction (HER) and zinc dendrite growth are...
Zinc-ion batteries are promising candidates for large-scale energy storage. The side reactions of the hydrogen evolution reaction (HER) and zinc dendrite growth are major challenges for developing high-performance zinc-ion batteries. In this paper, a supramolecular gel electrolyte (BLO-ILZE) was self-assembled in an ionic liquid (EMIMBF) with zinc tetrafluoroborate (Zn(BF)) on the separator in situ to obtain a gel electrolyte used in zinc-ion batteries. BLO-ILZE is demonstrated to significantly enhance conductivity over a broad temperature range between -70 and 100 °C. Interestingly, through testing and fitting, it is found that the supramolecular gel electrolyte satisfies the liquid state law over a wide temperature range, and even achieves high conductivity (2.12 mS cm) at -40 °C. It is equivalent to the conductivity of aqueous zinc-ion batteries (ZnSO/HO) at -10 °C, which is 2.33 mS cm. Moreover, the supramolecular gel electrolyte can effectively inhibit the HER, thus exhibiting a longer lifetime in Zn/Zn cells for 3470 h at 1 mA cm compared to the aqueous zinc-ion batteries with the Zn(BF) aqueous electrolyte (400 h at 1 mA cm). The assembled VO/BLO-ILZE/Zn full cells also showed cycling performance, with 5000 cycles at 0.5 mA g at room temperature, a capacity of 98%, and a coulombic efficiency of about 100%.
PubMed: 38932030
DOI: 10.3390/polym16121680 -
Polymers Jun 2024High-molecular-weight poly(L-lactide)--poly(ethylene glycol)--poly(L-lactide) (PLLA-PEG-PLLA) is a flexible and biodegradable bioplastic that has promising potential in...
Preparation of Poly(L-lactide)--poly(ethylene glycol)--poly(L-lactide)/Zinc Oxide Nanocomposite Bioplastics for Potential Use as Flexible and Antibacterial Food Packaging.
High-molecular-weight poly(L-lactide)--poly(ethylene glycol)--poly(L-lactide) (PLLA-PEG-PLLA) is a flexible and biodegradable bioplastic that has promising potential in flexible food packaging but it has no antibacterial ability. Thus, in this work, the effect of zinc oxide nanoparticles (nano-ZnOs) which have antimicrobial activity on various properties of PLLA-PEG-PLLA was determined. The addition of nano-ZnOs enhanced the crystallization, tensile, UV-barrier, and antibacterial properties of PLLA-PEG-PLLA. However, the crystallization and tensile properties of nanocomposite films decreased again as the nano-ZnO increased beyond 2 wt%. The nano-ZnO was well distributed in the PLLA-PEG-PLLA matrix when the nano-ZnO content did not exceed 2 wt% and exhibited some nano-ZnO agglomerates when the nano-ZnO content was higher than 2 wt%. The thermal stability and moisture uptake of the PLLA-PEG-PLLA matrix decreased and the film's opacity increased as the nano-ZnO content increased. The PLLA-PEG-PLLA/ZnO nanocomposite films showed good antibacterial activity against bacteria such as and . It can be concluded that nano-ZnOs can be used as a multi-functional filler of the flexible PLLA-PEG-PLLA. As a result, the addition of nano-ZnOs as a nucleating, reinforcing, UV-screening, and antibacterial agent in the flexible PLLA-PEG-PLLA matrix may provide protection for both the food and the packaging during transportation and storage.
PubMed: 38932010
DOI: 10.3390/polym16121660 -
Polymers Jun 2024In view of exploring the possibility of upcycling aerospace scrap, cure characteristics of out-of-spec carbon fiber prepregs are investigated in this study. The cure...
In view of exploring the possibility of upcycling aerospace scrap, cure characteristics of out-of-spec carbon fiber prepregs are investigated in this study. The cure behavior of the prepreg is examined in the form of the mechanical cure conversion state of the material using a Dynamic Mechanical Analyzer (DMA). Cure kinetics is modeled by comparing the storage modulus at the start of the reaction (E') and instantaneously (E') during isothermal experiments with those of the fully cured material (E') obtained from dynamic scans. The glass transition temperature T and the extent of reaction before gelation are modeled using the DiBenedetto model, where the T of each laminate is determined in a DMA, per standard ASTM D7028. The mechanical properties, the extent of cure, and the glass transition temperature of the cured laminates were determined according to industry and international standards. The maximum conversion at temperatures between 100 °C and 140 °C is approximately 80% (±5%). The modeled rate of conversion shows a reasonable match with the experimental data, exhibiting a maximum reaction rate at about 30-40% of the cure conversion. The predicted evolution of the T as a function of cure conversion using the DiBenedetto model provides a 94% match with the experimental data. The multi-stage cure cycle based on the models offers shorter cycle times and high-quality laminates. The mechanical test results indicate approximately a 13% and 15% decrease in tensile strength and modulus, respectively, compared to pristine ones. The experimental extent of cure of the cured laminates (95.4%) is in close agreement with that predicted by the model (97%). The porosity in the laminates is estimated to be approximately 2.4%, which is acceptable in several industries.
PubMed: 38931975
DOI: 10.3390/polym16121625 -
Polymers Jun 2024The upcoming energy transition requires not only renewable energy sources but also novel electricity storage systems such as batteries. Despite Li-ion batteries being...
The upcoming energy transition requires not only renewable energy sources but also novel electricity storage systems such as batteries. Despite Li-ion batteries being the main storage systems, other batteries have been proposed to fulfil the requirements on safety, costs, and resource availability. Moving away from lithium, materials such as sodium, magnesium, zinc, and calcium are being considered. Water-based electrolytes are known for their improved safety, environmentally friendliness, and affordability. The key, however, is how to utilize the negative metal electrode, as using water-based electrolytes with these metals becomes an issue with respect to oxidation and/or dendrite formation. This work studied magnesium, where we aimed to determine if it can be electrochemically deposited in aqueous solutions with alginate-based additives to protect the magnesium. In order to do so, atomic force microscopy was used to research the morphological structure of magnesium deposition at the local scale by using a probe-the tip of a cantilever-as the active electrode, during charging and discharging. The second goal of using the AFM probe technology for magnesium deposition and stripping was an extension of our previous study in which we investigated, for lithium, whether it is possible to measure ion current and perform nonfaradaic impedance measurements at the local scale. The work presented here shows that this is possible in a relatively simple way because, with magnesium, no dendrite formation occurs, which hinders the stripping process.
PubMed: 38931965
DOI: 10.3390/polym16121615 -
Pharmaceutics Jun 2024Skin is the largest organ and a multifunctional interface between the body and its environment. It acts as a barrier against cold, heat, injuries, infections, chemicals,... (Review)
Review
Skin is the largest organ and a multifunctional interface between the body and its environment. It acts as a barrier against cold, heat, injuries, infections, chemicals, radiations or other exogeneous factors, and it is also known as the mirror of the soul. The skin is involved in body temperature regulation by the storage of fat and water. It is an interesting tissue in regard to the local and transdermal application of active ingredients for prevention or treatment of pathological conditions. Topical and transdermal delivery is an emerging route of drug and cosmetic administration. It is beneficial for avoiding side effects and rapid metabolism. Many pharmaceutical, technological and cosmetic innovations have been described and patented recently in the field. In this review, the main features of skin morphology and physiology are presented and are being followed by the description of classical and novel nanoparticulate dermal and transdermal drug formulations. The biophysical aspects of the penetration of drugs and cosmetics into or across the dermal barrier and their investigation in diffusion chambers, skin-on-a-chip devices, high-throughput measuring systems or with advanced analytical techniques are also shown. The current knowledge about mathematical modeling of skin penetration and the future perspectives are briefly discussed in the end, all also involving nanoparticulated systems.
PubMed: 38931938
DOI: 10.3390/pharmaceutics16060817