-
Polymers May 2024Waterproof and breathable membranes have a huge market demand in areas, such as textiles and medical protection. However, existing fluorinated nanofibrous membranes,...
Waterproof and breathable membranes have a huge market demand in areas, such as textiles and medical protection. However, existing fluorinated nanofibrous membranes, while possessing good waterproof and breathable properties, pose health and environmental hazards. Consequently, fabricating fluorine-free, eco-friendly waterborne membranes by integrating outstanding waterproofing, breathability, and robust mechanical performance remains a significant challenge. Herein, we successfully prepared waterborne silicone-modified polyurethane nanofibrous membranes with excellent elasticity, waterproofing, and breathability properties through waterborne electrospinning, using a small quantity of poly(ethylene oxide) as a template polymer and in situ doping of the poly(carbodiimide) crosslinking agent, followed by a simple hot-pressing treatment. The silicone imparted the nanofibrous membrane with high hydrophobicity, and the crosslinking agent enabled its stable porous structure. The hot-pressing treatment (120 °C) further reduced the pore size and improved the water resistance. This environmentally friendly nanofibrous membrane showed a high elongation at break of 428%, an ultra-high elasticity of 67.5% (160 cycles under 400% tensile strain), an air transmission of 13.2 mm s, a water vapor transmission rate of 5476 g m d, a hydrostatic pressure of 51.5 kPa, and a static water contact angle of 137.9°. The successful fabrication of these environmentally friendly, highly elastic membranes provides an important reference for applications in healthcare, protective textiles, and water purification.
PubMed: 38891452
DOI: 10.3390/polym16111505 -
Polymers May 2024Silicone-modified polyurethane (PUSX) refers to the introduction of a silicone short chain into the polyurethane chain to make it have the dual properties of silicone...
Silicone-modified polyurethane (PUSX) refers to the introduction of a silicone short chain into the polyurethane chain to make it have the dual properties of silicone and polyurethane (PU). It can be used in many fields, such as coatings, films, molding products, adhesives, and so on. The use of organic solvents to achieve the fiberization of silicone-modified polyurethane has been reported. However, it is challenging to achieve the fiberization of silicone-modified polyurethane based on an environmentally friendly water solvent. Herein, we report a simple and powerful strategy to fabricate environmentally friendly waterborne silicone-modified polyurethane nanofiber membranes through the addition of polyethylene glycol (PEG) with different molecular weights using electrospinning technology and in situ doping with three crosslinking agents with different functional groups (a polyoxazoline crosslinking agent, a polycarbodiimide crosslinking agent, and a polyisocyanate crosslinking agent) combined with various heating treatment conditions. The influence of PEG molecular weight on fiber formation was explored. The morphology, structure, water resistance, and mechanical properties were analyzed regarding the effect of the introduction of silicone into PU. The effects of the type and content of crosslinking agent on the morphology and physical properties of PUSX nanofiber membranes are discussed. These results show that the introduction of silicone can improve the water resistance and high temperature resistance of waterborne PU, and the addition of a crosslinking agent can further improve the water resistance of the sample, so that the sample can maintain good morphology after immersion. Crosslinking agents with different functional groups had different effects on the mechanical properties of PUSX nanofiber membranes due to different reactions. Among them, the oxazoline crosslinking agent had a significant effect on improving tensile strength, while the isocyanate crosslinking agent had a significant effect on improving the elongation at break. The PUSX nanofiber membrane prepared in this work did not use organic solvents that were harmful to humans and the environment, and it can be used in outdoor textiles, oil-water separation, medical health, and other fields.
PubMed: 38891447
DOI: 10.3390/polym16111500 -
Polymers May 2024This paper explores the interaction between cutting parameters and the geometric accuracy of machined holes in a variety of engineering plastics, with the aim of...
This paper explores the interaction between cutting parameters and the geometric accuracy of machined holes in a variety of engineering plastics, with the aim of improving manufacturing processes in the plastic processing industry. In the context of fast and precise manufacturing technology, the accuracy of drilled holes in polymers is of paramount importance, given their essential role in the assembly and functionality of finished parts. The objective of this research was to determine the influence of cutting speed and feed rate on the diameter and cylindricity of machined holes in six diverse types of plastics using a multilevel factorial design for analysis. The key message conveyed to the reader highlights that careful selection of cutting parameters is crucial to achieving high standards of accuracy and repeatability in plastic processing. The methodology involved structured experiments, looking at the effect of changing cutting parameters on a set of six polymer materials. A CNC machining center for drills and high-precision measuring machines were used to evaluate the diameter and cylindricity of the holes. The results of ANOVA statistical analysis showed a significant correlation between cutting parameters and hole sizes for some materials, while for others the relationship was less evident. The conclusions drawn highlight the importance of optimizing cutting speed and feed rate according to polymer type to maximize accuracy and minimize deviations from cylindricity. It was also observed that, under selected processing conditions, high- and medium-density polyurethane showed the best results in terms of accuracy and cylindricity, suggesting potential optimized directions for specific industrial applications.
PubMed: 38891438
DOI: 10.3390/polym16111490 -
Polymers May 2024The alveoli, critical sites for gas exchange in the lungs, comprise alveolar epithelial cells and pulmonary capillary endothelial cells. Traditional experimental models...
The alveoli, critical sites for gas exchange in the lungs, comprise alveolar epithelial cells and pulmonary capillary endothelial cells. Traditional experimental models rely on porous polyethylene terephthalate or polycarbonate membranes, which restrict direct cell-to-cell contact. To address this limitation, we developed AlveoMPU, a new foam-based mortar-like polyurethane-formed alveolar model that facilitates direct cell-cell interactions. AlveoMPU features a unique anisotropic mortar-shaped configuration with larger pores at the top and smaller pores at the bottom, allowing the alveolar epithelial cells to gradually extend toward the bottom. The underside of the film is remarkably thin, enabling seeded pulmonary microvascular endothelial cells to interact with alveolar epithelial cells. Using AlveoMPU, it is possible to construct a bilayer structure mimicking the alveoli, potentially serving as a model that accurately simulates the actual alveoli. This innovative model can be utilized as a drug-screening tool for measuring transepithelial electrical resistance, assessing substance permeability, observing cytokine secretion during inflammation, and evaluating drug efficacy and pharmacokinetics.
PubMed: 38891433
DOI: 10.3390/polym16111486 -
Polymers May 2024Dielectric elastomers, such as thermoplastic polyurethanes (TPUs), are widely used as the dielectric layer, encapsulation layer, and substrate of flexible and...
Dielectric elastomers, such as thermoplastic polyurethanes (TPUs), are widely used as the dielectric layer, encapsulation layer, and substrate of flexible and stretchable devices. To construct capacitors and actuators that work stably upon deformation, it has become urgent to investigate the evolution of dielectricity under stress and strain. However, the lack of effective methods for estimating the dielectric constant of elastomers under strain poses a big challenge. This study reports a device for the in situ measurement of the dielectric constant of TPU under strain. It is found that upon stretching TPU to a strain of 400%, its dielectric constant decreases from 8.02 ± 0.01 to 2.88 ± 0.25 (at 1 MHz). In addition, combined Fourier-transform infrared spectroscopy, the X-ray scattering technique, and atomic force microscopy were utilized to characterize the evolution of the microstructure under strain. The investigation under tensile strain reveals a decreased density and average size of polarized hard domains, along with a tendency of the molecular chains to align in parallel with the tensile stress. The evolution of the microstructures results in a reduction in the measured dielectric constant in TPU.
PubMed: 38891412
DOI: 10.3390/polym16111465 -
Foods (Basel, Switzerland) May 2024The application of organic fertilizers is one of the most important agricultural measures aimed at improving the flavor and productivity of , with the granulation and...
The application of organic fertilizers is one of the most important agricultural measures aimed at improving the flavor and productivity of , with the granulation and coating of organic fertilizers, which can reduce seepage losses of great significance to the ecosystem. In this study, Jingcai 8 tomato was selected as the test material. Headspace solid-phase microextraction and gas chromatography-mass spectrometry (HS-SPME-GC-MS) methods were used to investigate the effects of different pelletized organic fertilizers and various coating materials on the flavor profile of the tomatoes. The results indicated that 67 volatile organic compounds (VOCs) were identified in the tomato fruits and 62 volatile compounds were identified in the leaves under different fertilizer treatments. The volatile compound content of the fruits in the BP treatment group was 35.38 μg/g, which was higher than that in other treatment groups, and the volatile compound content of the leaves was lower. A differential compound analysis with log|fold change| ≥ 1 and variable important in projection (VIP) > 1 highlighted styrene, 3-methyl-1-butanol, and (E, E)-2,4-hexadienal as the major up-regulated compounds and methyl salicylate as the major down-regulated compound in the tomato fruit BCK (control) vs. BP. Moreover, the α-phellandrene content decreased in the tomato leaves. In addition, an analysis of the tomato fruit differential compounds and compounds with odor activity values (OAV) of ≥ 1, considering the OAV values of characteristic aroma compounds, identified key compounds affecting the flavor of the tomato fruits under the BP treatment. These included 2-nonenal, (E)-2-pentylfuran, trans-β-ionone, 1-penten-3-one, (E, E)-2,4-hexadienal, and 3-hexenol (fruity, floral, and herbaceous odors), (E, E)-2,4-heptadienal (fatty odor), and hexanal (green odor). The combined results analysis of the volatile compound content, differential compounds, and OAV values of characteristic aroma compounds aimed to clarify that the BP treatment group, which applied pelletized, large-grain organic fertilizer with polyurethane (pozzolanic + small-grain oil-coated + 2% paraffinic + 4% polyurethane) as a coating material, proved to be most effective in influencing the flavor of the tomato fruits. This finding lays the foundation for its potential commercial application in artificial orchards.
PubMed: 38890880
DOI: 10.3390/foods13111653 -
Scientific Reports Jun 2024The dissolution of soluble rocks (gypsum/anhydrite) beneath the Mosul Dam by water seepage has been observed upon the initial impoundment; consequently, several...
The dissolution of soluble rocks (gypsum/anhydrite) beneath the Mosul Dam by water seepage has been observed upon the initial impoundment; consequently, several sinkholes have been manifested in the vicinity of the dam site. Traditional grouting has been envisaged as a potential remedy; however this measure has not eradicated the problem. The main purpose of this study is to overcome the solubility of the gypsum/anhydrite rocks using chemical grouts. Rock samples were acquired from the Fatha Formation outcrop and problematic layers of brecciated gypsum situated at varying depths beneath the Mosul Dam. Two commercially available liquid polymers, polyurethane (PU) and a mixture of acrylic and cement (ARC) were used to investigate their sealing performance in halting of the solubility of the rocks (gypsum/anhydrite). To simulate the dissolution phenomenon under the influence of artificial hydraulic pressure of the dam and the water flow in its abutments, two distinct laboratory models were devised. The outcomes from the experimental study on both untreated and treated samples revealed that the acrylic-cement composite (ARC) and polyurethane (PU) are influential polymers in halting the solubility of the gypsum rock samples under both factors of water pressure and high-velocity water flow.
PubMed: 38890376
DOI: 10.1038/s41598-024-64593-5 -
ACS Omega Jun 2024Microplastics have been detected in various food types, suggesting inevitable human exposure. A major fraction may originate from aerial deposition and could be...
Microplastics have been detected in various food types, suggesting inevitable human exposure. A major fraction may originate from aerial deposition and could be contaminated by ubiquitous pollutants such as polycyclic aromatic hydrocarbons (PAHs). While data on the sorption of pollutants to microplastics are abundant, the subsequent desorption in the gastrointestinal tract (GIT) is less understood. This prompted us to systematically investigate the release of microplastics-sorbed PAHs at realistic loadings (44-95 ng/mg) utilizing a physiology-based in vitro model comprising digestion in simulated saliva, gastric, and small and large intestinal fluids. Using benzo[]pyrene as a representative PAH, desorption from different microplastics based on low density polyethylene (LDPE), thermoplastic polyurethanes (TPUs), and polyamides (PAs) was investigated consecutively in all four GIT fluid simulants. The cumulative relative desorption (CRD) of benzo[]pyrene was negligible in saliva simulant but increased from gastric (4 ± 1% - 15 ± 4%) to large intestinal fluid simulant (21 ± 1% - 29 ± 6%), depending on the polymer type. CRDs were comparable for ten different microplastics in the small intestinal fluid simulant, except for a polydisperse PA-6 variant (1-10 μm), which showed an exceptionally high release (51 ± 8%). Nevertheless, the estimated contribution of microplastics-sorbed PAHs to total human PAH dietary intake was very low (≤0.1%). Our study provides a systematic data set on the desorption of PAHs from microplastics in GIT fluid simulants.
PubMed: 38882100
DOI: 10.1021/acsomega.3c09380 -
ACS Omega Jun 2024Polymeric materials play a vital role in high-voltage insulation, but their insulating properties can deteriorate over time, leading to insulation failures. The presence...
Polymeric materials play a vital role in high-voltage insulation, but their insulating properties can deteriorate over time, leading to insulation failures. The presence of voids resulting from manufacturing defects or external stresses can create a highly divergent field, further contributing to this issue. However, certain polymers, such as polyurethane (PU), possess self-healing properties that enable them to repair these voids and restore a uniform electric field distribution, thereby ensuring the reliability of the insulation. Surprisingly, the potential of PU as an insulating material in high-voltage applications remains unexplored. However, the self-healing capability of PU decreases with an increase in the hardness of the material. Therefore, in this study, the dielectric breakdown properties of PU with different levels of hardness, rated on the Shore scale as 40° (soft), 70° (medium), and 90° (hard), were investigated. The AC and DC dielectric breakdown characteristics of these PU variants and dielectric spectra were examined. Additionally, the study explores the relationship between the dielectric properties and the hardness of the material. Our findings revealed that the dielectric breakdown strength of PU increases as the material's hardness is increased under both AC and DC electric stress. However, this may come at the cost of reduced self-healing capabilities of PU. Therefore, there is a need to balance the hardness of the material with its ability to recover from breakdown events. The findings from this study can be useful for researchers and engineers, as they offer valuable insights into the dielectric properties of PU at various hardness levels.
PubMed: 38882065
DOI: 10.1021/acsomega.4c00509 -
Bioactive Materials Oct 2024Previous studies have confirmed that intervertebral disc degeneration (IDD) is closely associated with inflammation-induced reactive oxygen species (ROS) and resultant...
Previous studies have confirmed that intervertebral disc degeneration (IDD) is closely associated with inflammation-induced reactive oxygen species (ROS) and resultant cell mitochondrial membrane potential (MMP) decline. Clearance of ROS in an inflammatory environment is essential for breaking the vicious cycle of MMP decline. Additionally, re-energizing the mitochondria damaged in the inflammatory milieu to restore their function, is equally important. Herein, we proposed an interesting concept of mitochondrion-engine equipped with coolant, which enables first to "cool-down" the inflammatory environment, next to restore the MMP, finally to allow cells to regain normal energy metabolism through materials design. As such, we developed a multi-functional composite composed of a reactive oxygen species (ROS)-responsive sodium alginate/gelatin hydrogel infused into a rigid 3D-printed thermoplastic polyurethane (TPU) scaffold. The TPU scaffold was coated with conductive polypyrrole (PPy) to electrophoretically deposit l-arginine, which could upregulate the Mammalian target of rapamycin () pathway, thus increasing MMP and energy metabolism to stimulate extracellular matrix synthesis for IVD repair. While the ROS-responsive hydrogel acting as the "mito-engine coolant" could scavenge the excessive ROS to create a favorable environment for IVD cells recovery. Demonstrated by and evaluations, the mito-engine system markedly promoted the proliferation and collagen synthesis of nucleus pulposus cells while enhancing the mitochondrial respiration and MMP under oxidative stress. Radiological and histological assessments revealed the efficacy of this system in IVD repair. This unique bioinspired design integrated biomaterial science with mitochondrial biology, presents a promising paradigm for IDD treatment.
PubMed: 38873262
DOI: 10.1016/j.bioactmat.2024.05.044