-
Polymers Jun 2024The aim of this study was to obtain three experimental resin-based cements containing GO and HA-Ag for posterior restorations. The samples (S0, S1, and S2) shared the...
The aim of this study was to obtain three experimental resin-based cements containing GO and HA-Ag for posterior restorations. The samples (S0, S1, and S2) shared the same polymer matrix (BisGMA, TEGDMA) and powder mixture (bioglass (LaO and Sr-Zr), quartz, GO, and HA-Ag), with different percentages of graphene oxide (0%, 0.1%, 0.2% GO) and silver-doped hydroxyapatite (10%, 9.9%, 9.8% HA-Ag). The physical-chemical properties (water absorption, degree of conversion), mechanical properties (DTS, CS, FS), structural properties (SEM, AFM), and antibacterial properties (, , , , and ) were investigated. The results showed that the mechanical properties, except for the diametral tensile test, increased with the rise in the %GO. After 28 days, water absorption increased with the rise in the %GO. The surface structure of the samples did not show major changes after water absorption for 28 days. The antibacterial effects varied depending on the samples and bacterial strains tested. After increasing the %GO and decreasing the %HA-Ag, we observed a more pronounced antibacterial effect. The presence of GO, even in very small percentages, improved the properties of the tested experimental cements.
PubMed: 38932093
DOI: 10.3390/polym16121743 -
Polymers Jun 2024Six differently charged amphoteric polyamidoamines, synthesized by the polyaddition of ,'-methylenebisacrylamide to alanine, leucine, serine, arginine (M-ARG), glutamic...
Six differently charged amphoteric polyamidoamines, synthesized by the polyaddition of ,'-methylenebisacrylamide to alanine, leucine, serine, arginine (M-ARG), glutamic acid (M-GLU) and a glycine/cystine mixture, were screened for their short-term phytotoxicity using a seed germination test. L. seeds were incubated in polyamidoamine water solutions with concentrations ranging from 0.156 to 2.5 mg mL at 25 ± 1 °C for 120 h. The seed germination percentage (%), an indicator of acute toxicity, and both root and shoot elongation, related to plant maturation, were the considered endpoints. The germination index () was calculated as the product of relative seed germination times relative radical growth. The % values were in all cases comparable to those obtained in water, indicating no detectable acute phytotoxicity of the polyamidoamines. In the short term, the predominantly positively charged M-ARG proved to be phytotoxic at all concentrations ( < 0.8), whereas the predominantly negatively charged M-GLU proved to be biostimulating at intermediate concentrations ( > 1) and slightly inhibitory at 2.5 mg mL (0.8 < < 1). Overall, polyamidoamine phytotoxicity could be correlated to charge distribution, demonstrating the potential of the test for predicting and interpreting the eco-toxicological behavior of water-soluble polyelectrolytes.
PubMed: 38932092
DOI: 10.3390/polym16121744 -
Polymers Jun 2024In the current research, we prepared a polymeric framework, {[Cu(CO)(CHN)]·HO·0.67(CHOH)]} () (where CO = oxalic acid; CHN = 2,2-bipyridine), and explored this...
In the current research, we prepared a polymeric framework, {[Cu(CO)(CHN)]·HO·0.67(CHOH)]} () (where CO = oxalic acid; CHN = 2,2-bipyridine), and explored this compound for adsorption of methylene blue (MB) and methyl orange (MO). The crystal structure of the compound consists of a Cu(ox)(bpy) unit connected via oxalate to form a 1D polymeric chain. This polymeric chain has adsorption capacities of 194.0 and 167.3 mg/g for MB and MO, respectively. The removal rate is estimated to be 77.6% and 66.9% for MB and MO, respectively. The plausible mechanisms for adsorption are electrostatic, π-π interaction, and OH-π interaction for dye stickiness. The adsorbent surface exhibits a negative charge that produces the electrostatic interaction, resulting in excellent adsorption efficiency at pH 7 and 8. The pseudo-first-order kinetic model is selected for the adsorption of MB and MO on the adsorbent. The reported compound has remarkable efficiency for sorption of organic dyes and can be useful in wastewater treatment.
PubMed: 38932091
DOI: 10.3390/polym16121742 -
Polymers Jun 2024Nanopatterning methods utilizing block copolymer (BCP) self-assembly are attractive for semiconductor fabrication due to their molecular precision and high resolution.... (Review)
Review
Nanopatterning methods utilizing block copolymer (BCP) self-assembly are attractive for semiconductor fabrication due to their molecular precision and high resolution. Grafted polymer brushes play a crucial role in providing a neutral surface conducive for the orientational control of BCPs. These brushes create a non-preferential substrate, allowing wetting of the distinct chemistries from each block of the BCP. This vertically aligns the BCP self-assembled lattice to create patterns that are useful for semiconductor nanofabrication. In this review, we aim to explore various methods used to tune the substrate and BCP interface toward a neutral template. This review takes a historical perspective on the polymer brush methods developed to achieve substrate neutrality. We divide the approaches into copolymer and blended homopolymer methods. Early attempts to obtain neutral substrates utilized end-grafted random copolymers that consisted of monomers from each block. This evolved into side-group-grafted chains, cross-linked mats, and block cooligomer brushes. Amidst the augmentation of the chain architecture, homopolymer blends were developed as a facile method where polymer chains with each chemistry were mixed and grafted onto the substrate. This was largely believed to be challenging due to the macrophase separation of the chemically incompatible chains. However, innovative methods such as sequential grafting and BCP compatibilizers were utilized to circumvent this problem. The advantages and challenges of each method are discussed in the context of neutrality and feasibility.
PubMed: 38932090
DOI: 10.3390/polym16121740 -
Polymers Jun 2024Despite the mechanical and physical properties of polyurethane foams (PUF), their application is still hindered by high inflammability. The elaboration of effective,...
Despite the mechanical and physical properties of polyurethane foams (PUF), their application is still hindered by high inflammability. The elaboration of effective, low-cost, and environmentally friendly fire retardants remains a pressing issue that must be addressed. This work aims to show the feasibility of the successful application of natural nanomaterials, such as halloysite nanotubes and nanocellulose, as promising additives to the commercial halogen-free, fire-retardant triphenyl phosphate (TPP) to enhance the flame retardance of open-cell polyurethane foams. The nanocomposite foams were synthesized by in situ polymerization. Investigation of the mechanical properties of the nanocomposite PUF revealed that the nanoscale additives led to a notable decrease in the foam's compressibility. The obtained results of the flammability tests clearly indicate that there is a prominent synergetic effect between the fire-retardant and the natural nanoscale additives. The nanocomposite foams containing a mixture of TPP (10 and 20 parts per hundred polyol by weight) and either 10 wt.% of nanocellulose or 20 wt.% of halloysite demonstrated the lowest burning rate without dripping and were rated as HB materials according to UL 94 classification.
PubMed: 38932089
DOI: 10.3390/polym16121741 -
Polymers Jun 2024A quantitative analysis of the morphology, as well as an analysis of the distribution of components and surface/interfacial properties in poly(lactic acid)(PLA) InegoTM...
A quantitative analysis of the morphology, as well as an analysis of the distribution of components and surface/interfacial properties in poly(lactic acid)(PLA) InegoTM 3251D, poly(ε-caprolactone) (PCL) Capa 6800 and nano-silica (SiO) Aerosil200 blends, was conducted in this research. The study aimed to improve the understanding of how PLA, PCL, and nano-SiO interact, resulting in the specific morphology and surface properties of the blends. Samples were produced by varying the concentration of all three components. They were analyzed using SEM, EDS mapping, water contact angle measurements, surface free energy calculation, adhesion parameter measurements, and FTIR-ATR spectroscopy. The results showed that the addition of SiO nanoparticles led to an increase in the contact angle of water, making the surface more hydrophobic. SEM images of the blends showed that increasing the PCL content reduced the size of spherical PCL elements in the blends. FTIR-ATR analysis showed that SiO nanoparticles influenced the structure ordering of PLA in the blend with equal portions of PLA and PCL. In the samples with a higher PCL content, the spherical elements present in the samples with a higher PLA/PCL ratio have been reduced, indicating better interactions at the interface between PLA, PCL, and SiO. SEM-EDS mapping of the PLA/PCL 100/0 blend surfaces revealed the presence of SiO clusters and the silicon (Si) concentration reaching up to ten times higher than the nominal concentration of SiO. However, with the addition of 3% SiO to the blend containing PCL, the structure became more granular. Specifically, Si protrusions in the sample PLA/PCL 90/10 with 3% SiO displayed 29.25% of Si, and the sample PLA/PCL 70/30 with 3% SiO displayed an average of 10.61% of Si at the protrusion locations. The results confirmed the affinity of SiO to be encapsulated by PCL. A better understanding of the interactions between the materials in the presented blends and the quantitative analysis of their morphology could improve the understanding of their properties and allow the optimization of their application for different purposes.
PubMed: 38932088
DOI: 10.3390/polym16121739 -
Polymers Jun 2024Fouling and biofouling remain significant challenges in seawater desalination plants. One practical approach to address these issues is to develop anti-biofouling...
Fouling and biofouling remain significant challenges in seawater desalination plants. One practical approach to address these issues is to develop anti-biofouling membranes. Therefore, novel hybrid zinc phthalocyanine/polyvinylidene fluoride-co-hexafluoropropylene (Zn(4-PPOx)Pc/PVDF-HFP) membranes were prepared by electrospinning to evaluate their properties against biofouling. The hybrid nanofiber membrane was characterized by atomic force microscopy (AFM), attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy, and contact angle measurements. The theoretical calculations of PVDF-HFP, Zn(4-PPOx)Pc), and Zn(4-PPOx)Pc/PVDF-HFP nanofibers were performed using a hybrid functional RB3LYP and the 6-31 G (d,p) basis set, employing Gaussian 09. DFT calculations illustrated that the calculated physical and electronic parameters ensured the feasibility of the interaction of PVDF-HFP with Zn(4-PPOx)Pc via a halogen-hydrogen bond, resulting in a highly stable and remarkably reactive structure. Moreover, molecular electrostatic potential (MEP) maps were drawn to identify the reactive regions of the Zn(4-PPOx)4Pc and PVDF-HFP/Zn(4-PPOx)4Pc nanofibers. Molecular docking analysis revealed that Zn(4-PPOx)Pc has highest binding affinity (-8.56 kcal/mol) with protein from (1N67) mainly with ten amino acids (ASP405, LYS374, GLU446, ASN406, ALA441, TYR372, LYS371, TYR448, LYS374, and ALA442). These findings highlight the promising potential of Zn(4-PPOx) Pc/PVDF-HFP nanocomposite membranes in improving the efficiency of water desalination by reducing biofouling and providing antibacterial properties.
PubMed: 38932087
DOI: 10.3390/polym16121738 -
Polymers Jun 2024In this study, we report an easy approach for the production of aqueous dispersions of C fullerene with good stability. Maleic acid copolymers, poly(styrene--maleic...
In this study, we report an easy approach for the production of aqueous dispersions of C fullerene with good stability. Maleic acid copolymers, poly(styrene--maleic acid) (SM), poly(N-vinyl-2-pyrrolidone--maleic acid) (VM) and poly(ethylene--maleic acid) (EM) were used to stabilize C fullerene molecules in an aqueous environment by forming non-covalent complexes. Polymer conjugates were prepared by mixing a solution of fullerene in N-methylpyrrolidone (NMP) with an aqueous solution of the copolymer, followed by exhaustive dialysis against water. The molar ratios of maleic acid residues in the copolymer and C were 5/1 for SM and VM and 10/1 for EM. The volume ratio of NMP and water used was 1:1.2-1.6. Water-soluble complexes (composites) dried lyophilically retained solubility in NMP and water but were practically insoluble in non-polar solvents. The optical and physical properties of the preparations were characterized by UV-Vis spectroscopy, FTIR, DLS, TGA and XPS. The average diameter of the composites in water was 120-200 nm, and the ξ-potential ranged from -16 to -20 mV. The bactericidal properties of the obtained nanostructures were studied. Toxic reagents and time-consuming procedures were not used in the preparation of water-soluble C nanocomposites stabilized by the proposed copolymers.
PubMed: 38932086
DOI: 10.3390/polym16121736 -
Polymers Jun 2024Biodegradable poly(butylene succinate--2-methyl succinate) (PBSMS)/cellulose nanocrystals (CNC) composites were successfully prepared at low CNC loadings with the aims...
Biodegradable poly(butylene succinate--2-methyl succinate) (PBSMS)/cellulose nanocrystals (CNC) composites were successfully prepared at low CNC loadings with the aims of improving crystallization and mechanical properties and extending the practical application of PBSMS. CNC is finely dispersed in the PBSMS matrix without obvious aggregations. The low content of CNC obviously promoted the crystallization behavior of PBSMS under different conditions. The spherulitic morphology study revealed that CNC, as an effective heterogeneous nucleating agent, provided more nucleation sites during the melt crystallization process. In addition, the nucleation effect of CNC was quantitatively evaluated by the following two parameters, i.e., nucleation activity and nucleation efficiency. The crystal structure and crystallization mechanism of PBSMS remained unchanged in the composites. In addition, as a reinforcing nanofiller, CNC significantly increased Young's modulus and the yield strength of PBSMS. The crystallization behavior and mechanical properties of PBSMS were significantly improved by the low content of CNC, which should be interesting and essential from the perspective of biodegradable polymer composites.
PubMed: 38932085
DOI: 10.3390/polym16121735 -
Polymers Jun 2024The antifungal agent, ketoconazole, and the anti-inflammatory drug, piroxicam, were incorporated into matrices of xanthan or oleic acid-esterified xanthan (Xn) and...
The antifungal agent, ketoconazole, and the anti-inflammatory drug, piroxicam, were incorporated into matrices of xanthan or oleic acid-esterified xanthan (Xn) and polyurethane (PU), to develop topical drug delivery systems. Compared to matrices without bioactive compounds, which only showed a nominal compressive stress of 32.18 kPa (sample xanthan-polyurethane) at a strain of 71.26%, the compressive resilience of the biomaterials increased to nearly 50.04 kPa (sample xanthan-polyurethane-ketoconazole) at a strain of 71.34%. The compressive strength decreased to around 30.67 kPa upon encapsulating a second drug within the xanthan-polyurethane framework (sample xanthan-polyurethane-piroxicam/ketoconazole), while the peak sustainable strain increased to 87.21%. The Weibull model provided the most suitable fit for the drug release kinetics. Unlike the materials based on xanthan-polyurethane, those made with oleic acid-esterified xanthan-polyurethane released the active ingredients more slowly (the release rate constant showed lower values). All the materials demonstrated antimicrobial effectiveness. Furthermore, a higher volume of piroxicam was released from oleic acid-esterified xanthan-polyurethane-piroxicam (64%) as compared to xanthan-polyurethane-piroxicam (44%). Considering these results, materials that include polyurethane and either modified or unmodified xanthan showed promise as topical drug delivery systems for releasing piroxicam and ketoconazole.
PubMed: 38932084
DOI: 10.3390/polym16121734