-
ACS Infectious Diseases Apr 2022The antinoroviral effect of copper ions is well known, yet most of this work has previously been conducted in copper and copper alloy surfaces, not copper ions in...
The antinoroviral effect of copper ions is well known, yet most of this work has previously been conducted in copper and copper alloy surfaces, not copper ions in solution. In this work, we characterized the effects that Cu ions have on human norovirus capsids' and surrogates' integrity to explain empirical data, indicating virus inactivation by copper alloy surfaces, and as means of developing novel metal ion-based virucides. Comparatively high concentrations of Cu(II) ions (>10 mM) had little effect on the infectivity of human norovirus surrogates, so we used sodium ascorbate as a reducing agent to generate unstable Cu(I) ions from solutions of copper bromide. We found that significantly lower concentrations of monovalent copper ions (∼0.1 mM) compared to divalent copper ions cause capsid protein damage that prevents human norovirus capsids from binding to cell receptors and induce a greater than 4-log reduction in infectivity of Tulane virus, a human norovirus surrogate. Further, these Cu(I) solutions caused reduction of GII.4 norovirus from stool in suspension, producing about a 2-log reduction of virus as measured by a reverse transcriptase-quantitative polymerase chain reaction. Sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) data indicate substantial major capsid protein cleavage of both GI.7 and GII.4 norovirus capsids, and TEM images show the complete loss of capsid integrity of GI.7 norovirus. GII.4 virus-like particles (VLPs) were less susceptible to inactivation by copper ion treatments than GI.7 VLPs based upon receptor binding and SDS-PAGE analysis of viral capsids. The combined data demonstrate that stabilized Cu(I) ion solutions show promise as highly effective noroviral disinfectants in solution that can potentially be utilized at low concentrations for inactivation of human noroviruses.
Topics: Alloys; Capsid Proteins; Catalysis; Copper; Ions; Norovirus; Virus Inactivation
PubMed: 35315654
DOI: 10.1021/acsinfecdis.1c00609 -
Frontiers in Immunology 2022Ti-5Cu alloy has been proved to have excellent mechanical properties and cell compatibility and has certain antibacterial properties due to the addition of Cu. However,...
Ti-5Cu alloy has been proved to have excellent mechanical properties and cell compatibility and has certain antibacterial properties due to the addition of Cu. However, there are few studies on the effects of Ti-5Cu alloy on macrophage polarization and immune-related bone formation. In this study, we prepared Ti-5Cu alloy by three-dimensional printing technology and found that Ti-5Cu alloy presented a much smoother surface compared with Ti. In addition, the CCK-8 results indicated the Ti-5Cu alloy had no cytotoxicity to RAW264.7 cells by co-culture. The results of inductively coupled plasma mass spectrometry showed that the concentration of Cu was 0.133 mg/L after 7 days of co-culture, and the CCK-8 results proved that Cu had no cytotoxicity to RAW264.7 at this concentration. Then, we studied the effects of Ti-5Cu alloy on macrophage polarization; it was shown that the Ti-5Cu alloy is more prone to modulate the RAW264.7 polarization towards the M2 phenotype and the conditioned medium derived from Ti-5Cu alloy significantly promoted the proliferation and osteogenic differentiation of MC3T3-E1 cells. However, when the expression of Oncostatin M (OSM) gene of RAW264.7 was knocked down, the osteogenic differentiation of MC3T3-E1 cells was decreased. This suggests that the OSM secreted by RAW264.7 co-cultured with Ti-5Cu alloy could accelerate the osteogenic differentiation of MC3T3-E1 cells by acting on OSMR/gp130 receptors.
Topics: Osteogenesis; Alloys; Titanium; Oncostatin M; Culture Media, Conditioned; Sincalide; Cytokine Receptor gp130; Macrophages; Phenotype; Printing, Three-Dimensional; Anti-Bacterial Agents
PubMed: 36275667
DOI: 10.3389/fimmu.2022.1001526 -
BioMed Research International 2017The objective of the study is to characterise the mechanical properties of Ti-15Zr binary alloy dental implants and to describe their biomechanical behaviour as well as...
The objective of the study is to characterise the mechanical properties of Ti-15Zr binary alloy dental implants and to describe their biomechanical behaviour as well as their osseointegration capacity compared with the conventional Ti-6Al-4V (TAV) alloy implants. The mechanical properties of Ti-15Zr binary alloy were characterised using Roxolid© implants (Straumann, Basel, Switzerland) via ultrasound. Their biomechanical behaviour was described via finite element analysis. Their osseointegration capacity was compared via an study performed on 12 adult rabbits. Young's modulus of the Roxolid© implant was around 103 GPa, and the Poisson coefficient was around 0.33. There were no significant differences in terms of Von Mises stress values at the implant and bone level between both alloys. Regarding deformation, the highest value was observed for Ti-15Zr implant, and the lowest value was observed for the cortical bone surrounding TAV implant, with no deformation differences at the bone level between both alloys. Histological analysis of the implants inserted in rabbits demonstrated higher BIC percentage for Ti-15Zr implants at 3 and 6 weeks. Ti-15Zr alloy showed elastic properties and biomechanical behaviours similar to TAV alloy, although Ti-15Zr implant had a greater BIC percentage after 3 and 6 weeks of osseointegration.
Topics: Alloys; Animals; Dental Implants; Finite Element Analysis; Humans; Materials Testing; Rabbits; Stress, Mechanical
PubMed: 29318142
DOI: 10.1155/2017/2785863 -
Scanning 2020The application prospect of biodegradable materials is being studied extensively. However, the high corrosion rate and its alloys in body fluids have been major...
The application prospect of biodegradable materials is being studied extensively. However, the high corrosion rate and its alloys in body fluids have been major limitations of the application of pure Mg (magnesium). To improve corrosion resistance of biodegradable AZ31 Mg alloy, we adopted microarc fluorination within a voltage range of 100-300 V in 46% hydrofluoric acid. To obtain morphologies, chemical compositions, and structural characteristics, field-emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction (XRD) were performed, respectively. Results showed that the coating was mainly composed of MgF. Electrochemical corrosion and immersion tests proved that the corrosion resistance of MAF-treated AZ31 Mg alloy was significantly improved compared with untreated AZ31 Mg alloy in HBSS (Hank's Balanced Salt Solution). Current densities of AZ31, MAF100, MAF150, MAF200, MAF250, and MAF300 were 342.4, 0.295, 0.228, 0.177, 0.199, and 0.212 A/cm, respectively. The roughness test indicated that samples under MAF treatment of 200 V, 250 V, and 300 V had large surface roughness. Meanwhile, the contact angle measurement and surface free energy test suggested that those samples had smaller contact angle and higher SFE than Ti. Thus, MAF-treated AZ31 Mg alloy might have promising application in various fields.
Topics: Alloys; Body Fluids; Coated Materials, Biocompatible; Corrosion; Magnesium; Microscopy, Electron, Scanning; Spectrometry, X-Ray Emission; Surface Properties; X-Ray Diffraction
PubMed: 33193944
DOI: 10.1155/2020/5936789 -
ACS Applied Bio Materials Dec 2022The present work explored the use of the selective laser melting (SLM) technique to develop a Zr-based bulk metallic glass (BMG) and investigate the influence of the...
The present work explored the use of the selective laser melting (SLM) technique to develop a Zr-based bulk metallic glass (BMG) and investigate the influence of the process parameters on obtaining different levels of surface roughness. Moreover, the potential of the additively manufactured BMG ZrCuAlNb (trade name AMLOY-ZR01) as an implant material was studied by evaluating the osteoblastic cell response to the alloy and its stability under simulated biological environments. The materials were characterized in terms of degree of crystallinity, surface roughness, and morphology, followed by a systematic investigation of the response of the MC3T3-E1 preosteoblastic cell line to the as-printed samples. The materials supported cell proliferation and differentiation of the preosteoblastic cells, with results comparable to the reference material Ti-6Al-4V. The surface microroughness and surface morphology (porous or groove-type laser tracks) investigated in this study did not have a significant effect on modulating the cell response. Ion release experiments showed a large increase in ion release under inflammatory conditions as compared to regular physiological conditions, which could be attributed to the increased local corrosion under inflammatory conditions. The findings in this work showed that the surface roughness of the additively manufactured BMG AMLOY-ZR01 can be tailored by controlling the laser power applied during the SLM process. The favorable cell response to the as-printed AMLOY-ZR01 represents of a significant advancement of the investigation of additively manufactured BMGs for orthopedic applications, while the results of the ion release study highlights the effect that inflammatory conditions could have on the degradation of the alloy.
Topics: Zirconium; Glass; Alloys; Corrosion; Porosity
PubMed: 36459395
DOI: 10.1021/acsabm.2c00764 -
Dental Materials Journal Apr 2022This study assessed the effect of a primer containing 10-methacryloyloxydecyl-(2-thiohydantoin-4-yl)propionate (MDTHP) on the bonding of noble metal alloys to an acrylic...
This study assessed the effect of a primer containing 10-methacryloyloxydecyl-(2-thiohydantoin-4-yl)propionate (MDTHP) on the bonding of noble metal alloys to an acrylic resin. Three noble metal alloys were selected as adherends, and V-Primer containing 6-(4-vinylbenzyl-n-propyl)amino-1,3,5-triazine-2,4-dithione was used as a comparative control. The disk specimens of each noble metal alloy were wet-ground and divided into three conditions: specimens primed with MDTHP primer or V-Primer, and specimens without priming. An acrylic resin was bonded to each specimen, and the specimens were performed the shear bond test. The MDTHP primer showed higher shear bond strength than the V-Primer for all specimens. X-ray photoelectron spectroscopic analysis showed that MDTHP was adsorbed on the Au-Pt-Pd alloy surface even after acetone cleaning. MDTHP binds not only with Cu but also with Au and Ag, promoting the bond strength of noble metal alloys. The effectiveness of MDTHP on dental noble metal alloys was suggested.
Topics: Alloys; Dental Alloys; Dental Bonding; Gold Alloys; Materials Testing; Methacrylates; Resin Cements; Shear Strength; Surface Properties; Thiohydantoins
PubMed: 34980767
DOI: 10.4012/dmj.2021-181 -
BioMed Research International 2015Surfaces of medical implants can be enhanced with the favorable properties of titanium-nitride (TiN). In a review of English medical literature, the effects of... (Review)
Review
Surfaces of medical implants can be enhanced with the favorable properties of titanium-nitride (TiN). In a review of English medical literature, the effects of TiN-coating on orthopaedic implant material in preclinical studies were identified and the influence of these effects on the clinical outcome of TiN-coated orthopaedic implants was explored. The TiN-coating has a positive effect on the biocompatibility and tribological properties of implant surfaces; however, there are several reports of third body wear due to delamination, increased ultrahigh molecular weight polyethylene wear, and cohesive failure of the TiN-coating. This might be due to the coating process. The TiN-coating process should be optimized and standardized for titanium alloy articulating surfaces. The clinical benefit of TiN-coating of CoCrMo knee implant surfaces should be further investigated.
Topics: Alloys; Coated Materials, Biocompatible; Humans; Knee Prosthesis; Orthopedics; Surface Properties; Titanium; Vitallium
PubMed: 26583113
DOI: 10.1155/2015/485975 -
Journal of Orthopaedic Surgery and... Feb 2020Additively manufactured porous metallic structures have recently received great attention for bone implant applications. The morphological characteristics and mechanical...
BACKGROUND
Additively manufactured porous metallic structures have recently received great attention for bone implant applications. The morphological characteristics and mechanical behavior of 3D printed titanium alloy trabecular structure will affect the effects of artificial prosthesis replacement. However, the mechanical behavior of titanium alloy trabecular structure at present clinical usage still is lack of in-depth study from design to manufacture as well as from structure to mechanical function.
METHODS
A unit cell of titanium alloy was designed to mimick trabecular structure. The controlled microarchitecture refers to a repeating array of unit-cells, composed of titanium alloy, which make up the scaffold structure. Five kinds of unit cell mimicking trabecular structure with different pore sizes and porosity were obtained by modifying the strut sizes of the cell and scaling the cell as a whole. The titanium alloy trabecular structure was fabricated by 3D printing based on Electron Beam Melting (EBM). The paper characterized the difference between the designs and fabrication of trabecular structures, as well as mechanical properties and the progressive collapse behavior and failure mechanism of the scaffold.
RESULTS
The actual porosities of the EBM-produced bone trabeculae are lower than the designed, and the load capacity of a bearing is related to the porosity of the structure. The larger the porosity of the structure, the smaller the stiffness and the worse the load capacity is. The fracture interface of the trabecular structure under compression is at an angle of 45 with respect to the compressive axis direction, which conforms to Tresca yield criterion. The trabeculae-mimicked unit cell is anisotropy. Under quasi-static loading, loading speed has no effect on mechanical performance of bone trabecular specimens. There is no difference of the mechanical performance at various orientations and sites in metallic workspace. The elastic modulus of the scaffold decreases by 96%-93% and strength reduction 96%-91%, compared with titanium alloy dense metals structure. The apparent elastic modulus of the unit-cell-repeated scaffold is 0.39-0.618 GPa, which is close to that of natural bone and stress shielding can be reduced.
CONCLUSION
We have systematically studied the structural design, fabrication and mechanical behavior of a 3D printed titanium alloy scaffold mimicking trabecula bone. This study will be benefit of the application of prostheses with proper structures and functions.
Topics: Alloys; Bone Substitutes; Cancellous Bone; Compressive Strength; Materials Testing; Printing, Three-Dimensional; Stress, Mechanical; Tissue Scaffolds; Titanium
PubMed: 32028970
DOI: 10.1186/s13018-019-1489-y -
Bioactive materials: In vitro investigation of different mechanisms of hydroxyapatite precipitation.Acta Biomaterialia Jan 2020Bioactive materials, able to induce hydroxyapatite precipitation in contact with body fluids, are of great interest for their bone bonding capacity. . The aim of this...
Bioactive materials, able to induce hydroxyapatite precipitation in contact with body fluids, are of great interest for their bone bonding capacity. . The aim of this paper is to compare bioactive materials with different surface features to verify the mechanisms of action and the relationship with kinetics and type of precipitated hydroxyapatite over time. Four different surface treatments for Ti/Ti6Al4V alloy and a bioactive glass were selected and a different mechanism of bioactivity is supposed for each of them. Apart from the conventional techniques (FESEM, XPS and EDX), less common characterizations (zeta potential measurements on solid surfaces and FTIR chemical imaging) were applied. The results suggest that the OH groups on the surface have several effects: the total number of the OH groups mainly affects hydrophilicity of surfaces, while the isoelectric points, surface charge and ions attraction mainly depend on OH acidic/basic strength. Kinetics of hydroxyapatite precipitation is faster when it involves a mechanism of ion exchange while it is slower when it is due to electrostatic effects . The electrostatic effect cooperates with ion exchange and it speeds up kinetics of hydroxyapatite precipitation. Different bioactive surfaces are able to differently induce precipitation of type A and B of hydroxyapatite, as well as different degrees of crystallinity and carbonation. STATEMENT OF SIGNIFICANCE: The bone is made of a ceramic phase (a specific type of hydroxyapatite), a network of collagen fibers and the biological tissue. A strong bond of an orthopedic or dental implant with the bone is achieved by bioactive materials where precipitation and growth of hydroxyapatite occurs on the implant surface starting from the ions in the physiological fluids. Several bioactive materials are already known and used, but their mechanism of action is not completely known and the type of precipitated hydroxyapatite not fully investigated. In this work, bioactive titanium and bioglass surfaces are compared through conventional and innovative methodologies. Different mechanisms of bioactivity are identified, with different kinetics and the materials are able to induce precipitation of different types of hydroxyapatite, with different degree of crystallinity and carbonation.
Topics: Alloys; Durapatite; Glass; Surface Properties; Titanium
PubMed: 31734414
DOI: 10.1016/j.actbio.2019.11.024 -
Scientific Reports Jan 2019Inhibiting osteoclasts and osteoclast precursors to reduce bone resorption is an important strategy to treat osteoclast-related diseases, such as peri-prosthetic...
Inhibiting osteoclasts and osteoclast precursors to reduce bone resorption is an important strategy to treat osteoclast-related diseases, such as peri-prosthetic osteolysis. In this study, our objective was to study the role of zoledronic acid (ZA), as a highly potent and nitrogen-containing bisphosphonate, in promoting osteogenesis and inhibiting osteoclastogenesis properties of magnesium (Mg)-based implants. ZA was chemically associated with calcium phosphate (CaP) deposited on magnesium-strontium (Mg-Sr) alloy, which was confirmed by the morphological observation, phase composition and drug releasing via SEM, XRD spectrum and High Performance Liquid Chromatography (HPLC), respectively. The in vitro performances indicated that ZA-CaP bilayer coating Mg-Sr alloy could enhance the proliferation and the osteogenic differentiation as well as the mineralization of pre-osteoblasts, however, induce the apoptosis and inhibit the osteoclast differentiation. We further investigated the possible molecular mechanisms by using Quantitative real-time PCR (qRT-PCR) and Western Blotting, and the results showed that ZA-CaP bilayer coating Mg-Sr alloy could regulate the osteogenesis and osteoclastogenesis through the Estrogen Receptor α (ERα) and NF-κB signaling pathway. Moreover, ZA-CaP bilayer coating Mg-Sr alloy could regulate the cross talk of osteoblast-osteoclast and increase the ratio of OPG: RANKL in the co-culture system through OPG/RANKL/RANK signaling pathway, which promoting the balance of bone remodeling process. Therefore, these promising results suggest the potential clinical applications of ZA pretreated Mg-Sr alloys for bone defect repairs and periprosthetical osteolysis due to the excessive differentitation and maturation of osteoclasts.
Topics: Alloys; Animals; Calcification, Physiologic; Cell Differentiation; Coated Materials, Biocompatible; Mice; Osteoblasts; Osteoclasts; Osteogenesis; RAW 264.7 Cells; Strontium; Zoledronic Acid
PubMed: 30700724
DOI: 10.1038/s41598-018-37091-8